Split system installation Richmond homes need starts with a question most quotes skip: where the outdoor unit can actually go. A split pairs an indoor head with an outdoor unit, joined by insulated copper refrigerant lines, a drain hose and a cable. More than half of Richmond's occupied dwellings are flats or apartments (53.0%, ABS 2021 Census), and most of the rest are terraces and other attached homes, so balconies, owners corporation rules and small rear courtyards shape the job. Peak Air Conditioning Richmond fits wall, floor console and large-capacity splits, back to back or with a longer pipe run in neat cover duct, and sets out the model, the kilowatt size and the pipe route in a free written quote after an inspection. Bookings run from 6am to 10pm, seven days. Call 0468 046 042 to book an inspection.
GET A FREE QUOTE
Peak Air Conditioning Richmond installs, repairs, services and cleans heating and cooling systems across Richmond and 12 nearby suburbs. Two things set out what a buyer gets before any work is booked: a written quote that itemises the job, and one phone line that covers all 12 services from 6am to 10pm. Each trade's work is done under the licence it requires: an ARC refrigerant handling licence for refrigerant work, a licensed gasfitter registered with the Building and Plumbing Commission for gas work, and a licensed electrician, who issues a Certificate of Electrical Safety, for wiring.
Peak Air Conditioning Richmond
Mitsubishi Electric's buying guide defines a split system as any air conditioner with separate indoor and outdoor units. The indoor half comes in different shapes for different rooms, and the shape decides where the pipes leave the wall and where the warm or cool air lands. The four choices below cover the indoor units most Richmond rooms are fitted with, and the five capacity steps Melbourne cost guides price them by.
The high-wall head is the familiar split: a slim indoor unit mounted near the ceiling, with the outdoor unit on the far side of the wall or further along a pipe route. The Australian Government's Energy Rating site groups air conditioners into cooling only, heating only, and heating and cooling models, and calls the heating and cooling type reverse cycle, also known as a heat pump. In Melbourne that dual role is the norm rather than an extra. Mitsubishi Electric lists reverse cycle heating as a standard feature of its MSZ-AP series, with a guaranteed outdoor heating range down to minus 15°C. Cooling-only wall units are still sold, such as Daikin's Alira X Cooling Only, so the quote names which type is being fitted. A reverse cycle installation that replaces a gas room heater has its own discount rules and running-cost case, set out on the reverse cycle air conditioning page.
A floor console sits low on the wall, near skirting height, instead of up near the ceiling. Daikin sells its split range as either wall mounted or floor standing, and points its floor models at rooms where upper wall installation is not possible and at homes where heating is the priority for more months of the year, because a unit mounted lower warms the ground more effectively. That suits a room whose upper wall is taken up by tall windows, picture rails or a sloping ceiling. The install changes with it: the pipes and drain leave the back of the console close to the floor, so the wall penetration sits low and the drain starts its fall from a lower point. Where summer cooling matters as much as winter heat, a high-wall head is often the better fit, since Daikin notes wall units are mounted high for better airflow and circulation of conditioned air.
Wikipedia describes the typical Richmond house as having two bedrooms at the front and the family room and kitchen at the back. Where that rear space has been opened into one combined kitchen, dining and living room, a bedroom-sized head can struggle to reach the far end of it. Large-capacity wall splits fill that gap. Daikin describes its XL Series as large capacity models designed for large open plan living, and Mitsubishi Electric's MSZ-AP series runs up to 7.8 kW. A bigger head needs a matching outdoor unit and draws more power, so the switchboard and the outdoor position are both checked at the inspection before the size is confirmed. When the goal is the whole floor rather than one large room, ducted air conditioning becomes worth pricing alongside it.
Those five figures are the capacity steps the Melbourne cost tables use to price split systems, from a small bedroom unit up to a large living-area head. Mitsubishi Electric is plain that sizing is not as simple as reading off a room's square metres, and calls a professional heat load calculation essential. That calculation takes in the room's length, width and ceiling height, which sides face the sun, the size, type and orientation of its windows and doors, its insulation and the local climate. A front bedroom on a shaded street and a rear room with a west-facing glass wall can share a floor area and still land on different steps. The heat load result, not the floor area, settles which of the five a room needs. The capacity panel on the government Energy Rating label then confirms how many kilowatts a chosen model actually delivers at set outdoor temperatures.


Peak Air Conditioning Richmond
A split system goes in to the manufacturer's installation manual, and Mitsubishi Electric's manual for its MSZ-AP wall splits shows the sequence clearly. Its tool list alone says a lot about the job: a 65 mm hole saw, a level, a torque wrench, a flare tool, and a gauge manifold and vacuum pump rated for R32 refrigerant. The four stages below follow the manual's order, from fixing the bracket to the first start-up.
The indoor head hangs on a steel installation plate. The manual asks for that plate to be fixed level into a structural member such as a wall stud, with enough screws that it cannot vibrate. It recommends a mounting height of 1.8 m to 2.3 m above the floor, in a spot where air is not blocked, where warm or cool air spreads across the whole room and where the filter can be lifted out easily. The pipe hole is then core drilled at 65 mm diameter, with the outdoor end 5 to 7 mm lower than the indoor end so water runs outside rather than back into the wall. A sleeve lines the hole and putty seals the gap around the pipes. Because the hole goes right through an external wall, its position is checked from the outside first, so it clears downpipes, window frames and the boundary.
Two copper refrigerant lines, the interconnecting cable and the drain hose pass through the wall together, taped into one bundle with the drain hose below the refrigerant piping. The manual calls for copper or seamless copper-alloy pipe, 8 mm of insulation on the lines and a bending radius of at least 100 mm so the pipe is never kinked. Every pipe on the outdoor side is insulated, valves included, with extra insulation where the run passes through a ceiling space or cupboard so condensation cannot form. Outside, the bundle usually runs in a rigid cover duct fixed to the wall, which gives a tidy line and meets the manual's instruction to embed or protect refrigerant piping from external damage. The drain hose must point downward for its whole length: the manual warns against raising it, letting it wave or leaving its tip in water, because faulty drain work lets water drop from the unit and damage household goods.
A new split arrives with its stop valves fully closed and capped, so the refrigerant stays sealed in the outdoor unit while the new copper lines are still full of air and moisture. After the joints are pressure tested with oxygen-free nitrogen, a vacuum pump is connected to the service port on the gas-side valve. Mitsubishi Electric's manual has the lines pumped down until 500 microns is reached, then left for one to two minutes to confirm the gauge does not move, which shows the pipework holds a vacuum. Only then are both stop valves opened fully, and the manual notes that running with them part-open lowers performance. The Australian Refrigeration Council's Cool Change bulletin explains why the order matters: clean, leak-free lines are what allow moisture to be removed properly during evacuation.
With the valves open, the system starts on a test run. On the MSZ-AP the emergency operation switch is pressed once for cooling or twice for heating, and the test run lasts 30 minutes. The remote is checked next, and the indoor unit beeps when it receives a signal. The manual also notes that after the compressor stops it will not restart for 3 minutes, a protective delay that can look like a fault to a new owner. At handover, the manual asks the installer to explain the remote controller, the auto restart that resumes the last setting after a blackout, and how to remove and clean the air filters. Mitsubishi Electric's filter guide suggests cleaning them every two weeks in peak seasons, while a yearly air conditioning service takes care of the coil, the drain and the refrigerant checks.
Peak Air Conditioning Richmond
Two pieces of paperwork separate a compliant split system install from a shortcut one: the refrigerant licence and the electrical certificate. Both are explained below. Alongside them, Peak Air Conditioning Richmond gives a free written quote after an inspection, naming the model and its kilowatt size, where the indoor head and outdoor unit go and how the pipes travel between them, so two quotes can be compared on the same terms. Inspections and installs can be booked from 6am to 10pm, seven days. That window matters in a suburb where the ABS 2021 Census counted 54.7% of homes as rented, because a tenant, a landlord and a property manager often all need a time that works.
Australian law requires anyone who handles refrigerant or works on refrigeration and air conditioning equipment to hold a refrigerant handling licence, issued by the Australian Refrigeration Council under the ARCtick scheme. The council's definition of handling covers installing and commissioning that equipment whether or not refrigerant is present, so mounting and connecting even a pre-charged split is licensed work. The council also issues a restricted licence aimed at split systems, covering their installation and decommissioning. Manufacturers repeat the rule: Mitsubishi Electric's installation manual states that in Australia only technicians holding the appropriate ARC licence should install the product. The practical step for a buyer is to ask for the technician's licence number and keep it with the quote and the invoice. The manufacturer warranty applies when the unit is installed to the manufacturer's requirements, which is why the licensed steps above matter.
The electrical side carries its own rules. Mitsubishi Electric's manual states that, to comply with AS/NZS 3000, the wiring rules, the cable between the indoor and outdoor units must be installed by a licensed electrical contractor. Where a split needs new electrical work, such as a new circuit from the switchboard, Energy Safe Victoria requires a Certificate of Electrical Safety under the Electricity Safety Act 1998, and the electrician must give the customer a copy. For non-prescribed work that copy is due within 30 days. Prescribed work, a separate category, must also be inspected by a licensed electrical inspector, and the electrician states which category applies. The certificate is worth filing with the system's paperwork, because Victorian rental providers must have all electrical installations checked by a licensed or registered electrician every 2 years.


Peak Air Conditioning Richmond
The figures below are indicative ranges from independent Melbourne cost guides and one Melbourne installer's published benchmarks, all dated 2026. They are not the business's own prices. The real figure comes from the written quote after an inspection, because the same unit can be a simple back-to-back job, with the indoor and outdoor units on opposite sides of one wall, or a long run through a terrace roof.
Climate Control Solutions, a Melbourne installer that last reviewed its figures in July 2026, lists indicative installed prices of $1,900 to $2,500 for 2.5 kW, $2,300 to $2,900 for 3.5 kW, $2,700 to $3,500 for 5.0 kW, $3,300 to $4,300 for 7.1 kW and $3,700 to $4,700 for 8.0 kW. It puts the simplest common case, a 3.5 kW back-to-back job, at around $2,100 to $2,600. The whatsthedamage Melbourne table, updated November 2026, runs wider at each step: $1,250 to $2,625 at 2.5 kW, $1,900 to $3,675 at 5 kW, $2,300 to $4,725 at 7 kW and $3,150 to $5,800 at 9 kW. The spread inside each band is likely to reflect the brand, the star rating and how easy the install is, which is why the quote names all three.
Multi-head systems are priced by the number of indoor heads on the outdoor unit. The whatsthedamage Melbourne table puts a supplied and installed 2-head system at $4,200 to $7,900, with $5,800 typical, and a 4-head system at $7,350 to $12,600, with $8,900 typical. Climate Control Solutions sets the two options side by side for a pair of rooms: two separate 3.5 kW splits at about $4,600 to $5,800 installed, against a 2-head multi-head at around $4,000 to $5,200. On those figures a multi-head can come in a little cheaper for two rooms, but the gap is narrow enough that outdoor space and the trade-offs in the next section tend to decide it. Neither table prices a 3-head system separately, so that is quoted on the job.
Paying only for installation, with the unit bought elsewhere, has its own price band. Whatsthedamage puts install-only work on a customer-supplied split at $735 to $1,575 in Melbourne, with about $1,000 typical. Hipages, a national guide, gives $600 to $1,000 for a basic installation and $1,000 to $2,000 for larger or more complex ones, with installer labour at $80 to $110 an hour. Before buying, it is worth confirming the capacity against a heat load check, because a model chosen on price alone can turn out too small for the room and that cannot be corrected on the day. The unit is still fitted to its own manufacturer's manual, since the manufacturer warranty applies when it is installed to the manufacturer's requirements.
The back-to-back price assumes a short pipe run through one wall, and three things push a quote above it. A longer run needs more copper, insulation and cover duct, and past a point more refrigerant: on Mitsubishi Electric's MSZ-AP25 to AP42, the factory charge covers 10 m of pipe, with 20 g of refrigerant added for each extra metre, up to a 20 m maximum. Height is the second: an outdoor unit on a second-storey wall bracket or a roof usually needs ladders, scaffolding or roof access, and more labour to lift and secure it. A new circuit is the third, and Climate Control Solutions suggests allowing roughly $450 for the licensed electrical work. Taking out an old unit is a separate line again, which the same installer puts at about $250 per unit.
Peak Air Conditioning Richmond
With only a narrow price gap between a 2-head system and two separate splits, the choice turns on how each one behaves day to day. Mitsubishi Electric defines a multi-head as multiple indoor units connected to a single outdoor unit, and the three points below are the practical results of sharing that one outdoor unit.
The limit is set by the outdoor unit's ports and capacity. Mitsubishi Electric's MXZ range shows the steps: the 5.2 kW MXZ-2F52 has 2 ports, the 5.4 kW MXZ-3F54 has 3, the 7.1 kW and 8.0 kW models have 4, the 10.0 kW MXZ-5F100 has 5 and the 12.0 kW MXZ-6F120 has 6. The brand's rule is that the larger the outdoor unit's capacity, the more indoor units it can connect. Output is shared among the heads running at the same time, so the heads can add up to more than the outdoor rating. In the brand's own example, an MSZ-AP35 and an MSZ-AP50 on one MXZ-4F71, both cooling, get up to 2.8 kW and 4.0 kW, while the AP50 alone would give its full 5.0 kW.
Each room on a multi-head keeps its own remote and its own set temperature, but not its own mode. Mitsubishi Electric's buying guide states that all units connected to the same outdoor unit must run in the same mode, either heating or cooling, and its multi-head page describes rooms setting temperatures without affecting each other within that shared mode. For a household that heats or cools the whole home together, the rule matters less. It shows up in the shoulder seasons and in homes with very different rooms, such as a sunny upstairs bedroom wanting cooling on a spring afternoon while a shaded ground-floor room wants heat. Separate splits let each room pick its own mode at any time. Heads that are not needed on a multi-head can simply be switched off, leaving more of the shared output for the rooms in use.
The shared outdoor unit is also a single point of failure. Every head draws its heating and cooling from the same outdoor unit, so a fault there stops every connected room at once, while separate splits leave the other rooms running while one is repaired. That follows from how the system is built; it is not a claim about how often multi-heads fail. Against it sits the space saving Mitsubishi Electric highlights: one outdoor unit takes up less space outside and has less impact on the exterior design of the house than three or four. On a terrace with a small rear courtyard, or an apartment with one balcony, that saving can outweigh the risk. Where one room has to stay conditioned no matter what, such as a home office or a nursery, a separate split for that room keeps it independent.


Peak Air Conditioning Richmond
Once the size is set, three things separate one split from another of the same capacity: how efficiently it heats and cools, how loud it runs and who makes it. The Australian Government's Energy Rating advice is to choose the size and features needed first, then use the star rating to compare similar models.
The Zoned Energy Rating Label must be shown in store on single-split air conditioners up to 30 kW. It gives a seasonal efficiency rating for three climate zones, hot, average and cold, on a scale of 1 to 10 stars, with heating and cooling rated separately. Mitsubishi Electric's MSZ-AP25, for example, carries heating stars of 3.5, 3 and 3 and cooling stars of 6, 5.5 and 6 across the hot, average and cold zones. For a Richmond home the figures that count are the ones for its own zone, which the Energy Rating Calculator finds by postcode, and the heating stars deserve as much weight as the cooling stars when a split heats through winter. Stars compare like with like only: the label guidance notes that ratings of models with different heating or cooling capacities cannot be compared.
The same label carries two noise figures in dB(A), one for the indoor unit and one for the outdoor unit. Mitsubishi Electric notes that lower decibel ratings mean quieter running, which matters most in bedrooms and living areas; its MSZ-AP heads run as low as 18 dB(A) in heating mode, and the AP series Night Mode cuts the outdoor unit's noise by up to 3 dB. In Richmond the outdoor figure can matter more than the indoor one, because the unit often sits close to a neighbour's window. EPA Victoria treats a heating air conditioner as unreasonable if it can be heard in a habitable room of another home on weekdays before 7am or after 10pm, with later cut-offs for cooling. A quieter outdoor unit gives more margin inside those hours.
Daikin's split range is sold as wall mounted or floor standing, with wall models including the Alira X, Zena, Cora, XL Series and FTXF Series, in both reverse cycle and cooling-only versions. Daikin reports being voted the most trusted air conditioner brand for four consecutive years, from 2023 to 2026, in Reader's Digest Australia's Trusted Brands survey. Mitsubishi Electric's wall range is led by the MSZ-AP series, running from 2.5 kW to 7.8 kW on R32 refrigerant, with its MXZ outdoor units for multi-head systems. Fujitsu and Panasonic are other well-known names in split systems, and a model from any of these brands can be compared on the same terms: capacity, heating and cooling stars for the home's zone, and the indoor and outdoor noise figures. Whichever brand is chosen, it is installed to that maker's own manual.
Peak Air Conditioning Richmond
Mitsubishi Electric's manual lists what a good outdoor position needs: good, dust-free airflow, shelter from rain and direct sun as far as possible, a rigid wall or support that will not add to operating sound or vibration, and a spot where neighbours are not annoyed by the noise or the hot or cool air. Richmond's housing makes each of those harder. Wikipedia describes the suburb as a mix of converted warehouse residences, high-rise flats and Victorian-era terraces, and the three positions below cover most of them.
Most Richmond houses, Wikipedia notes, are single-fronted Victorian homes built from the 1850s to the 1930s on long, thin blocks, with the living space at the back and, traditionally, the toilet or outhouse outside at the rear. That rear yard or courtyard is often the most practical ground-level spot for an outdoor unit serving the back rooms. The manual's checklist applies closely there: the unit sits level on a solid base or brackets, with clear air on its inlet and outlet sides, and a loop in the pipework near the unit is advised to reduce the vibration passed into the building. Semi-detached and row houses share side walls, so the unit is kept off a shared wall where the layout allows, and its discharge is pointed away from the neighbouring yard. The manual also warns against a spot where small animals may live, which rules out tucking the unit under a deck or into a dense corner.
In an apartment, the balcony is usually the only place for the outdoor unit, which brings the building's rules into play. Victoria's model rules for owners corporations, which apply where an owners corporation has not made its own rule on the item, say an owner or occupier must get written approval before changing the external appearance of their lot. A condenser on a balcony, or a cover duct running down an outside wall, is the kind of change that rule is written for. The owners corporation cannot unreasonably withhold approval, but it may attach reasonable conditions to protect other owners' quiet enjoyment, the structure or the common property, such as where the unit sits or how it is screened. Applying with the written quote in hand, showing the unit's size, its position and the pipe route, gives the committee what it needs to decide.
When there is no courtyard or balcony to use, the outdoor unit goes up, either on brackets on an upper-storey wall or on a flat or low-pitched roof. Mitsubishi Electric's manual allows for high mounting but asks that the unit's legs be secured, and it limits the height difference between the indoor and outdoor units on its MSZ-AP models to 12 m. A high position keeps the yard free and can move the noise source further from a neighbour's window, but it is harder to reach afterwards. Mr Duct Cleaning notes that a unit high on a second-storey wall or on a roof needs extra equipment to clean, so an extra charge may apply, and its standard prices assume an outdoor unit no more than 2 m above the ground. Choosing a high mount is therefore a trade between a neat pipe run today and the access cost of every later service visit.


Call the one number any day between 6am and 10pm. The booking notes the system type, the fault or the job, the address, who needs to be present (owner, tenant, agent or building manager) and any building access rules. Same-day visits are arranged where possible.

A technician inspects the site and the existing system or the planned unit positions, then gives a written quote listing equipment, labour, extras and old unit removal. For repairs, the diagnosis comes first and any part is quoted before it is ordered. Work starts once the quote is accepted.

Each trade works under the licence it needs: ARC for refrigerant, a BPC-registered gasfitter for gas and a licensed electrician for wiring. The system is then tested, the controls are explained, and paperwork such as a Certificate of Electrical Safety or a gas compliance certificate is handed over where the job requires one.
Melbourne cost guides put a supplied and installed back-to-back split at around $1,250 to $2,625 for 2.5 kW and $1,475 to $2,950 for 3.5 kW (whatsthedamage, November 2026), and Climate Control Solutions puts a 3.5 kW back-to-back job at about $2,100 to $2,600. Larger 7 and 9 kW units cost more, and a 2-head multi-head system is listed at $4,200 to $7,900. A long pipe run, a high outdoor unit or a new circuit adds to these ranges. These are indicative figures, and a free written quote is given after an inspection of the home.
No single model uses the least electricity in every home, because a correctly sized unit matters as much as the brand. The Energy Rating advice is to choose the capacity first, then compare similar models by their stars on the Zoned Energy Rating Label, which rates heating and cooling separately for hot, average and cold zones. Mitsubishi Electric notes that units with higher star ratings use less energy for the same performance. For a split that heats through a Melbourne winter, compare the heating stars for the home's own zone, which the Energy Rating Calculator finds by postcode.
A single back-to-back wall split is usually installed within a day. The work covers fixing the bracket, drilling the wall, running and insulating the lines, pressure testing and evacuating them, and a test run, which on Mitsubishi Electric's MSZ-AP lasts 30 minutes. Long pipe runs, an upper-storey or roof position, a new circuit and multi-head systems all take longer. In an apartment the start date can also wait on owners corporation approval, and the written quote sets out the expected timing.
The right size comes from a heat load calculation, not from floor area alone. Mitsubishi Electric's buying guide lists the factors: the room's length, width and ceiling height, which sides face the sun, the size and orientation of the windows, the insulation and the local climate. Melbourne cost guides price split systems in steps of 2.5, 3.5, 5, 7 and 9 kW, and two rooms with the same floor area can need different steps. The inspection before the written quote is where that calculation is done.
It depends on the home and how its rooms are used. A multi-head runs several indoor heads from one outdoor unit, which saves outdoor space, but every head must run in the same heating or cooling mode, the output is shared among the heads running at once, and a fault in the outdoor unit stops every room. Separate splits keep each room independent, at the cost of an outdoor unit for each one. Melbourne cost guides show only a small price gap between the two for a pair of rooms, so outdoor space and daily use usually decide it.
Yes. Install-only work on a customer-supplied split runs about $735 to $1,575 in Melbourne, with around $1,000 typical (whatsthedamage, November 2026). Check the capacity against the room's heat load before buying, because an undersized unit cannot be fixed on installation day. Manufacturers such as Mitsubishi Electric state that in Australia only technicians with the appropriate ARC licence should install their units, and any new circuit needs a licensed electrician and a Certificate of Electrical Safety. Peak Air Conditioning Richmond can quote install-only work, and the manufacturer warranty applies when the unit is installed to the manufacturer's requirements.
GET A FREE QUOTE
BUSINESS
SERVICES
OPERATING HOURS
Sun: 6:00am - 10:00pm
Mon: 6:00am - 10:00pm
Tue: 6:00am - 10:00pm
Wed: 6:00am - 10:00pm
Thu: 6:00am - 10:00pm
Fri: 6:00am - 10:00pm
Sat: 6:00am - 10:00pm