Ducted heating Richmond homes can use comes in two forms: a gas ducted heater that burns natural gas, or an electric ducted system that heats with a reverse cycle heat pump and can also cool. Both push warm air through ducts in the roof or under the floor to outlets in each room. Richmond's housing shapes the job: Wikipedia describes most of its houses as single-fronted Victorian homes on long, thin blocks, and the ABS 2021 Census counts 53.0% of its dwellings as flats or apartments. Peak Air Conditioning Richmond sizes the heater from a heat load calculation, plans where the unit, flue and outlets go, has every gas connection made by a licensed gasfitter registered with the Building and Plumbing Commission, and sets it all out in a free written quote. Bookings run from 6am to 10pm, seven days. Call 0468 046 042 to arrange an inspection.
GET A FREE QUOTE
Peak Air Conditioning Richmond installs, repairs, services and cleans heating and cooling systems across Richmond and 12 nearby suburbs. Two things set out what a buyer gets before any work is booked: a written quote that itemises the job, and one phone line that covers all 12 services from 6am to 10pm. Each trade's work is done under the licence it requires: an ARC refrigerant handling licence for refrigerant work, a licensed gasfitter registered with the Building and Plumbing Commission for gas work, and a licensed electrician, who issues a Certificate of Electrical Safety, for wiring.
Peak Air Conditioning Richmond
The Australian Government's YourHome guide describes ducted air heaters as systems that circulate hot air through roof or underfloor ducts, and notes that they can make that heat from gas or from electricity, with electric systems also able to cool. That one sentence holds the main choice on this page. The three parts below set out what each kind of system is and which ranges carry each one, before the later sections deal with sizing, cost and how the two compare.
A gas ducted heater is a central gas furnace. A burner warms a heat exchanger, a fan blows household air across it, and the ducts carry the warm air to each room. Each model carries a gas energy efficiency star rating, and Rinnai's current Brivis ducted gas range shows how wide the spread is. The StarPro 6 is rated 6 stars and comes in 15.0, 23.0, 29.0 and 35.0 kW. The StarPro 5 and StarPro 4 are rated 5 and 4 stars, each in 21, 30 and 35 kW. The Buffalo BX5C is a 5-star heater in 20 and 30 kW, and the Buffalo BX3C a 3-star heater in 15.5, 20 and 26 kW. Two compact models sit between those steps: the Classic Compact at 3.0 stars and the Classic Wombat at 3.8. The kW figure is the heater's output, chosen from the heat load of the house, and the star rating is how much gas it uses to make that heat. Prices by star rating appear in the cost section and the running-cost gap in the comparison section, so this list stays a plain map of what is on the market.
Electric ducted heating is a ducted reverse cycle air conditioner doing its winter job. The Australian Government's Energy Rating site notes that air conditioners can also be known as heat pumps, and that reverse cycle models both heat and cool. In heating mode the outdoor unit draws warmth from the outside air, refrigerant carries it into a fan coil in the roof or under the floor, and the same ducts and outlets deliver it to each room. There is no burner, no flue and no gas line. Rinnai, for example, sells a ducted reverse cycle range from 7.0 kW to 24.0 kW with up to 8 individual zones, and describes those systems as providing heating in winter and cooling in summer. Because the system holds refrigerant, it is RAC equipment and its pipework falls under refrigerant handling licensing, covered further down. How a heat pump keeps heating as the outdoor air drops is explained on the reverse cycle air conditioning page, so this page stays on the ducted form and on replacing gas with it.
Two names come up most often in Melbourne ducted gas heating, and both now sit inside larger companies. Brivis is part of Rinnai Australia: the Brivis website now says so and sends visitors to Rinnai's pages for ducted heating, evaporative cooling and spare parts. Braemar is a Seeley International brand, founded in 1938, whose range covers ducted gas heating, gas wall furnaces, ducted add-on cooling, hybrid heating and ducted reverse cycle systems. Braemar describes one of its heaters as the world's first 7 star equivalent ducted gas heater, and footnotes the claim as a star rating equivalent based on Australian Gas Association results under AS/NZS 5263.1.6:2020. That is the brand's own claim, not an independent rating. People searching for Brivis electric ducted heating should know that neither the Brivis nor the Rinnai site lists a Brivis-branded electric ducted system today: Rinnai sells its ducted reverse cycle range under the Rinnai name. Brands are named here as plain facts, and the model is chosen at the quote to suit the house and the budget.
Peak Air Conditioning Richmond
Brivis's installer's manual for its Classic ducted gas heaters lists the rules an installation must follow, among them AS 5601 for gas installations, AS/NZS 5141 for residential heating and cooling systems and AS 4254 for ductwork. The four parts below cover the decisions that matter most for winter performance: the heater's size, the outlet layout, the flue and gas supply, and duct size for any cooling planned later. The manual's figures belong to the models it covers, and each heater is installed to its own manual.
Rinnai's guidance on choosing a ducted system lists four inputs: total floor area, ceiling height, insulation and glazing, and orientation and climate zone. It adds that installers use a whole-of-home heat load calculation to settle the size, and Brivis's installer's manual likewise recommends its own sizing guide for estimating heating requirements. YourHome puts the aim simply: make sure the system is the right size for the house. Floor area alone does not answer it. Two houses with the same number of square metres can need different heaters if one has tall ceilings, bare windows or an uninsulated roof. The calculation is also where the outlet count starts, because each heater suits a limited number of outlets: Brivis's outlet chart gives its smallest external Classic model a range of 4 to 8 open outlets and its largest internal model up to 17. No manufacturer page read for this site publishes a table matching home sizes to kW, so no such guide is given here. The heat load result, not the bedroom count, picks the step in the range.
YourHome notes that floor outlets are often better than ceiling outlets for heating, because warm air naturally rises, and that ceiling outlets can work too, especially where rooms are sealed from draughts to the outdoors. Brivis's manual shows how the two layouts differ in practice. It describes typical domestic outlets as 300 mm by 100 mm floor registers or 150 mm round ceiling diffusers. A ceiling system should draw its return air at a low level, since a high-level return can reduce performance. The fan is also set differently: Brivis asks for a temperature rise of 35 to 40 °C above the return air at the nearest floor outlet, but 25 to 30 °C for a ceiling system. At commissioning, its starting point is living areas fully open, bedrooms half open and wet areas a quarter open, with a minimum number of outlets always left open so the heater does not overheat. Whether a given Richmond house has the subfloor room for floor ducts is something the inspection confirms, not an assumption.
Energy Safe Victoria lists a partly or totally blocked flue, and an appliance installed without adequate ventilation, among the causes of high carbon monoxide levels, so the flue and air supply are part of the installation design. For its external Classic heaters, Brivis's manual sets flue terminal clearances in accordance with AS 5601. They include 300 mm horizontally from an openable window or door, 1,000 mm from a gas meter, 500 mm from an electricity meter or fuse box, and 1,500 mm from an openable window or door in the direction the flue discharges. For roof and underfloor models, the flue must end outside the building, horizontal runs must rise at least 20 mm per metre, and a twin-wall flue may run to 6 m. On gas supply, the manual asks for the pipe and the gas meter to be sized so the heater holds its required pressure at full consumption while every other gas appliance runs at full capacity too, and for a gas cock beside the heater. Carbon monoxide testing of a heater already in service is a servicing job, separate from the installation.
Ducts sized only for heating can limit a home that later wants cooling. YourHome states plainly that ducts need to be larger if they are also used for cooling, so a household that expects to add cooling, or to move to an electric ducted system, can have the duct sizes chosen for that from the start. Brivis's manual sets the general duct standard: ductwork that is well insulated and airtight, with a minimum insulation rating of R1.0 (R1.5 in some areas), fastened to its fittings with duct tape in accordance with AS 4254, and correctly sized with smooth bends so air flows quietly. The manual also notes that insulated, fire rated duct is mandatory under building codes. The return air grille needs the same thought, since the manual sizes it to accept the system's full airflow and lists a larger grille where a filter is fitted. Choosing the duct size at the start avoids paying for whole-house duct replacement later, which the cost section prices, and the choice between the two cooling routes is set out in the comparison section below.
Peak Air Conditioning Richmond
A ducted heating job can touch three regulated trades: gas fitting, refrigerant handling and electrical work. The parts below set out how each one is handled on a job and what paperwork the household receives, followed by what the written quote contains. None of it depends on taking a claim on trust, because each item can be checked against a licence card, a certificate or the quote itself.
Energy Safe Victoria's advice is direct: always use a licensed gasfitter for any installation, repair or renovation that involves gas. On a gas ducted job, Peak Air Conditioning Richmond has the gas connection, the gas line and the flue work carried out by a licensed gasfitter (registered with the Building and Plumbing Commission). Brivis's own installer's manual says the same in its own words: the gas supply must be installed by a licensed gas fitter. The Building and Plumbing Commission requires a compliance certificate for the installation or replacement of any Type A gas appliance, whatever the cost of the job, and for installing or changing consumer gas piping. The certificate must be issued to the customer within five days of completing the work, and only licensed plumbers can issue one. Energy Safe Victoria also suggests asking to see the gasfitter's licence card and checking the registered classes printed on its back. A household can do that on the day and keep the certificate with the heater's records.
An electric ducted system is refrigeration and air conditioning equipment, and the ARC states that any person who handles refrigerant or works on RAC equipment must hold a refrigerant handling licence. That covers installing the fan coil, running the refrigerant pipes to the outdoor unit, and the pressure test and evacuation before the system is charged. The electrical side has its own rule. Energy Safe Victoria explains that a Certificate of Electrical Safety is required by the Electricity Safety Act 1998, and that the customer receives a copy within 30 days for non-prescribed work. Gas heaters are not exempt from electrical work either: Brivis's manual has its Classic heaters plugged into a 10 amp fixed switched socket beside the heater, with the 240 volt wiring installed by a licensed electrician, so a new heater in a roof or subfloor with no power point needs one. On these jobs the refrigerant work is done under an ARC licence and the wiring by a licensed electrician, with each certificate handed over.
The quote follows an inspection because the price depends on things only the house can show: how much heat it loses, how much room the roof or subfloor has, and what state any existing ducts are in. The written quote then names the heater by model with its output in kW, and for a gas heater its star rating, or for an electric system its heating capacity in kW. It states whether the existing ducts are reused or replaced, how many outlets there are and whether they sit in the floor or the ceiling, where the heater goes, and the flue route and gas line work for a gas unit. Certificates and the expected timing are listed too, so nothing is left to a phone conversation. Inspections and bookings run from 6am to 10pm, seven days. With 54.7% of Richmond dwellings rented in the ABS 2021 Census, a ducted heating job often involves an owner, an agent and a tenant, and a long booking window helps fit the visit around all three.
Peak Air Conditioning Richmond
The figures below come from independent Melbourne cost guides published or updated in 2026. They are indicative ranges, not the business's own prices, and the real figure comes from the written quote after the inspection. Servicing and repair prices for an existing heater belong to the service and repairs page, so this section covers new heaters, replacement heaters, ductwork and the switch to electric.
The whatsthedamage Melbourne cost table, updated November 2026, puts gas ducted heating supply and installation at $4,000 to $11,550, with $7,350 typical. Homeupkeep's Melbourne gas ducted guide, updated June 2026, breaks the price down by star rating and output, all supplied and installed: a 3-star 16 kW heater at $3,800 to $5,200, a 4-star 20 kW heater at $4,800 to $6,400, a 5-star 23 kW heater at $5,800 to $7,800 and a 6-star 30 kW heater at $7,200 to $10,000. Homeupkeep attaches brand labels to some rows, and its 4-star row names the Brivis Buffalo, which Rinnai's own range lists only at 3 and 5 stars, so the rows are best read by star and kW rather than by brand. The spread inside each row reflects the exact model, the number of outlets, how hard the roof or subfloor is to work in, and whether the ducts are new or reused. A higher-star heater costs more to buy, which the running-cost comparison below weighs against.
When a heater is replaced on ducts that are still sound, the price is mostly the new heater, the gas and flue connections and the labour to remove the old unit. The cost guides do not publish a separate heater-only swap price, so homeupkeep's supply-and-install rows above, from $3,800 to $5,200 for a 3-star 16 kW heater up to $7,200 to $10,000 for a 6-star 30 kW heater, are the closest published guide. Ductwork is the item that moves the total most. The whatsthedamage Melbourne table prices whole-house ductwork replacement with new insulated flexible ducts at $2,000 to $6,300, with $3,775 typical. Old ducts that are torn, crushed or thinly insulated waste heat in the roof, and if cooling is planned they may also be too small. The quote prices the heater and the ducts as separate lines, so a household can see what each part costs before deciding.
Converting to electric usually means a ducted reverse cycle system in place of the gas heater, and the price follows the home. The whatsthedamage Melbourne table puts standard ducted reverse cycle for a 3-bedroom home, or a single-storey 4-bedroom with good roof access, at $8,400 to $14,700, with $11,550 typical, and premium or zoned systems for larger and two-storey homes at $12,600 to $23,100. QuickAir's 2026 Melbourne guide gives $5,000 to $8,000 for a small 1 to 2-bedroom home. The Victorian Energy Upgrades program lists discounts of up to $2,520, $4,200 and $5,530 for 10, 16 and 22.4 kW systems replacing a ducted gas heater, for approved products only, with the details on the ducted air conditioning page. No cost guide read for this page publishes a price for a heater-position electric unit such as Braemar's Dominator, so that route is priced at the quote. Capping the old gas supply is gas work, done by a licensed gasfitter.
Peak Air Conditioning Richmond
With the systems described above, this section deals only with the trade-offs: what each costs to run through winter, how each handles summer, and when whole-home ducting makes sense against heating room by room. Water-based hydronic heating is a third choice with its own trade-offs, set out on its own page.
Homeupkeep's Melbourne guide estimates that a typical home running a gas ducted heater 4 to 6 hours a day through winter spends $850 to $1,800 on gas, and that newer 6-star heaters run 30 to 40% cheaper than 3-star ones. That is a cost guide's estimate, weaker than a government figure, but it shows why the star rating matters on a heater that runs every winter evening. The official figure for switching is the Victorian Energy Upgrades program's: energy bill savings of up to $1,140 a year when a ducted gas heater is removed or replaced with an efficient reverse cycle system. Energy.vic.gov.au adds a second effect: a dual-fuel home pays two bills and two service charges, while an all-electric home pays one of each. Its estimate of around $1,900 a year in savings applies to switching all of a home's gas appliances to efficient electric ones, not to the heater alone, so it is not a heater figure. No source read for this page gives a per-hour running cost for electric ducted heating, and manufacturer claims point both ways, so the government figures are the safer guide.
A household that wants ducted heating and cooling has two routes. The first is one electric ducted reverse cycle system that does both, with no gas connection at all. The second keeps a gas heater for winter and adds cooling to the same ducts. Rinnai lists its Brivis ICE DualComfort add-on, from 13 to 22 kW, as compatible with the StarPro series, and its ICEbox DualComfort, at 10, 13 and 15 kW, as compatible with the Buffalo series, with duct work that can run under the floor or in the roof space. Braemar's range also includes ducted add-on cooling. Older heaters need checking first: Brivis's manual notes that its Classic heaters have no on-board add-on cooling connection and need an extra relay. The add-on route keeps the gas bill and the two-yearly gas heater service that Energy Safe Victoria recommends, while the single electric system drops both. Either way, ducts sized for cooling, covered in the installation section, decide how well summer works.
Ducted heating heats the whole home from one central unit, which Rinnai lists first among its benefits, along with even temperatures from room to room and vents built into the floor or ceiling. A split system heats the room it is mounted in, so whole-home warmth means a unit in each room that needs it. Each approach has a cost the other avoids. YourHome notes that ducted systems are less energy efficient because they need energy for fans to push air around the house through the ducts, and that ducts leak heat if they are not well insulated and sealed. Zoning narrows the gap: the Buffalo BX5C, for example, is ZonePlus compatible for up to 4 zones, so living areas and bedrooms can be heated at different times. Home size matters as well. The ABS 2021 Census counts 66.2% of Richmond dwellings with one or two bedrooms, and in a small home a split system in the living area may heat most of the space people use, while a larger house with several rooms in daily use suits ducting better.
Peak Air Conditioning Richmond
This page covers replacing a gas ducted heater: when it is time, and what it can be replaced with. Whether a particular fault is worth repairing first, and the signs of a heater that is starting to fail, belong to the ducted heating service and repairs page. The three parts below take the replacement decision from age to the two main replacement routes.
Homeupkeep's Melbourne gas ducted guide advises replacing the whole unit at 15 to 20 years, and planning financially for replacement at 18 to 20 years regardless of how it is running. That is a cost guide's rule of thumb, not a manufacturer's figure or a regulation, but it gives a household a planning window. Energy Safe Victoria adds a safety angle: if a gas heater is old, or has not been serviced for several years, it suggests considering a replacement. For anyone weighing the electric route, Rinnai's guidance on ducted air conditioning puts a typical life at 12 to 20 years with correct installation and maintenance, and notes that ducting may last longer than the mechanical parts. That last point matters for both routes: a heater nearing 20 years may sit on ducts that can be reused, or on ducts that need replacing too. Planning the replacement before the heater stops, rather than after a winter breakdown, leaves time to compare both routes and check the ducts properly.
The simplest replacement keeps gas and the existing ducts and fits a newer heater in the old one's place. Rinnai describes its Buffalo BX3C as an easy changeover model for this kind of job, and a household moving from an old heater to a higher-star unit gets the lower gas use described in the comparison section. A like-for-like swap still involves checks. The new heater's outlet limits have to suit the outlets already in the house, since Brivis's manual sets both a minimum and a maximum number of open outlets for each model. If the new heater is larger, the gas line and meter must still hold the manual's required pressure with every other gas appliance running, which Brivis checks at commissioning against a minimum of 1.1 kPa for natural gas. The flue terminal is checked against current clearances, and the old ducts are checked for tears and thin insulation. Each replacement is gas work under a compliance certificate.
A newer route keeps the ducts but drops the gas. Braemar's Dominator Series 2 is built for this: Seeley International says it uses all-electric reverse cycle technology in an indoor unit designed to fit the same position as a ducted gas heater, directly replacing the existing gas heater and leaving all other components intact. Those are the brand's claims. The indoor unit is paired with a new Braemar outdoor unit, and Seeley lists pipe runs of up to 75 m between the two, two models with heating capacities of 12.1 kW and 17.9 kW, R32 refrigerant, and zoning for 4 zones as standard, expandable to 8. The job itself has several parts. A licensed gasfitter disconnects and caps the gas heater's supply, an ARC-licensed technician runs and tests the refrigerant pipes, a licensed electrician connects the power, and the existing ducts are checked, because YourHome notes that ducts need to be larger for cooling. Prices for this route are covered in the cost section.
Peak Air Conditioning Richmond
Richmond's housing differs sharply from the Victorian average. The ABS 2021 Census counts 30.7% of its dwellings as semi-detached, row or terrace houses and townhouses and 53.0% as flats or apartments, against 13.9% and 12.1% for Victoria. Each housing type raises its own question about where a ducted heater can go, and the three parts below take them in turn.
Wikipedia describes most Richmond houses as single-fronted Victorian homes built from the 1850s to the 1930s, typically on long, thin blocks with two bedrooms at the front and the family room and kitchen at the back. A gas ducted heater has three possible homes in a house like that, and Brivis's manual sets the rules for each. An external model sits outside on a level concrete pad, with 500 mm of service clearance at the front, 300 mm at each end and 1,000 mm above, plus the flue clearances from windows and doors. A roof-space model needs a 600 mm wide passage from the roof access to the heater and a level platform. An underfloor model needs at least 200 mm below the floor structure and a 50 mm concrete base. Homeupkeep notes that external cabinet units are the cheapest to service. On a narrow block, a side passage may be too tight for the external clearances and a low subfloor may rule out the underfloor option, so which location works is decided at the inspection, house by house.
Where the roof is the only option but the access hatch is small or the space is shallow, the heater's shape matters as much as its output. Rinnai describes its Brivis Classic Compact as low profile, compact and splittable, in 15.0, 19.5, 23.5 and 30.0 kW, and its Classic Wombat, in 15.0, 21.0 and 28.0 kW, as splittable for easy handling. A heater that comes apart can be carried through a smaller opening and reassembled in the roof. The roof-space rules in Brivis's manual still apply once it is up there: the structure under the heater has to carry the extra load, there must be fixed access, a normal ladder or steps, a walkway of at least 19 mm particle board, a platform extending 750 mm out from the service sides, and permanent lighting switched at the hatch. Electric swap units need room too. Seeley lists its Dominator indoor unit at 1,148 mm wide, 530 mm deep and 802 mm high, so a tight roof is measured before either route is chosen.
Rinnai lists the basic requirement for gas ducted heating as ductwork with sufficient roof or underfloor space, and many apartments have neither. Richmond's apartments range from converted warehouses such as The Malthouse, a conversion of silos into apartments, to high-rise flats, and the ABS 2021 Census counts 66.2% of the suburb's dwellings with one or two bedrooms. A gas ducted heater also needs a flue that ends outside the building, which a mid-floor flat may not be able to provide. Whether a given apartment can take ducted heating is a case-by-case question, often involving the owners corporation, and in some buildings the answer is no. Where ducts will not fit, a reverse cycle wall unit in the main living area is the alternative to price. For rentals, Consumer Affairs Victoria requires a fixed heater in the main living area, energy efficient for agreements from 29 March 2023, and the Victorian Energy Upgrades page states that a broken rental space heater that cannot be repaired after 1 March 2027 must be replaced with an efficient reverse cycle air conditioner.

Call the one number any day between 6am and 10pm. The booking notes the system type, the fault or the job, the address, who needs to be present (owner, tenant, agent or building manager) and any building access rules. Same-day visits are arranged where possible.

A technician inspects the site and the existing system or the planned unit positions, then gives a written quote listing equipment, labour, extras and old unit removal. For repairs, the diagnosis comes first and any part is quoted before it is ordered. Work starts once the quote is accepted.

Each trade works under the licence it needs: ARC for refrigerant, a BPC-registered gasfitter for gas and a licensed electrician for wiring. The system is then tested, the controls are explained, and paperwork such as a Certificate of Electrical Safety or a gas compliance certificate is handed over where the job requires one.
Melbourne cost guides put gas ducted heating supply and installation at around $4,000 to $11,550, with $7,350 typical (whatsthedamage, November 2026). Homeupkeep's rows run from $3,800 to $5,200 for a 3-star 16 kW heater to $7,200 to $10,000 for a 6-star 30 kW heater. New insulated ductwork for the whole house adds about $2,000 to $6,300, and electric ducted reverse cycle for a 3-bedroom home is listed at $8,400 to $14,700. These are indicative ranges, and a free written quote follows an inspection.
A central heater, either a gas burner or an electric heat pump, warms air that a fan pushes through ducts in the roof or under the floor to outlets in each room. YourHome describes this as hot air circulated through ducts to supply convective heat. A return air grille draws cooler air back to the heater to be warmed again. A thermostat, which Brivis places on an internal wall in the main living area about 1,500 mm above the floor, switches the system on and off to hold the set temperature.
Yes. YourHome notes that ducted air heaters can make heat from gas or electricity, and that electric systems can also cool. Electric ducted heating is a ducted reverse cycle air conditioner, which the Energy Rating site notes is also known as a heat pump. It draws heat from the outdoor air and needs no gas line or flue. Braemar's Dominator Series 2 is one electric unit made to fit where a gas ducted heater used to sit.
It can be. Energy.gov.au describes ducted gas heating as expensive to operate because of its gas use and the electricity for its fans, and homeupkeep estimates $850 to $1,800 a winter on gas for a typical Melbourne home running 4 to 6 hours a day. A higher-star heater, zoning and well-sealed, insulated ducts all lower the cost. The Victorian Energy Upgrades program lists bill savings of up to $1,140 a year when a ducted gas heater is replaced with an efficient reverse cycle system.
Yes, by two main routes. One replaces the whole system with ducted reverse cycle, which the Victorian Energy Upgrades program discounts by up to $5,530 for a 22.4 kW approved system replacing a ducted gas heater. The other fits an electric unit, such as Braemar's Dominator Series 2, in the gas heater's place and keeps the existing ducts, which the brand says stay intact. Either way, a licensed gasfitter disconnects and caps the old gas supply.
Homeupkeep's Melbourne guide advises replacing a gas ducted heater at 15 to 20 years and planning for replacement at 18 to 20 years regardless. That is a cost guide's rule of thumb, not a manufacturer's figure. Regular servicing affects how a heater ages, and Energy Safe Victoria suggests considering replacement for a heater that is old or has not been serviced for several years. Peak Air Conditioning Richmond can inspect an older heater and price both a gas and an electric replacement.
GET A FREE QUOTE
BUSINESS
SERVICES
OPERATING HOURS
Sun: 6:00am - 10:00pm
Mon: 6:00am - 10:00pm
Tue: 6:00am - 10:00pm
Wed: 6:00am - 10:00pm
Thu: 6:00am - 10:00pm
Fri: 6:00am - 10:00pm
Sat: 6:00am - 10:00pm