Air conditioning Collingwood work here covers split systems, multi-head systems, reverse cycle heat pumps, ducted heating and cooling, servicing, cleaning, repairs and regas. Collingwood is a City of Yarra suburb 3 km north-east of the Melbourne CBD, bounded by Smith Street, Alexandra Parade, Hoddle Street and Victoria Parade. Its homes are compact: the ABS 2021 Census counts 68.2% of occupied dwellings as flats or apartments and 25.6% as semi-detached, row or terrace houses or townhouses, with only 5.8% separate houses, against 73.4% across Victoria. It also counts 64.3% of homes as rented, so a job here can involve an owners corporation, a landlord or an agent as well as the person living in the home. Each job starts with an inspection and a written quote, and the phone line is open 6am to 10pm, seven days.
GET A FREE QUOTE
Peak Air Conditioning Richmond installs, repairs, services and cleans heating and cooling systems across Richmond and 12 nearby suburbs. Two things set out what a buyer gets before any work is booked: a written quote that itemises the job, and one phone line that covers all 12 services from 6am to 10pm. Each trade's work is done under the licence it requires: an ARC refrigerant handling licence for refrigerant work, a licensed gasfitter registered with the Building and Plumbing Commission for gas work, and a licensed electrician, who issues a Certificate of Electrical Safety, for wiring.

Small homes set the order of air conditioning work in Collingwood. The ABS 2021 Census puts the average dwelling at 1.9 bedrooms, against 3.1 for Victoria, and counts 27.9% of homes with one bedroom and 49.9% with two. So the three H3s below follow the stages a small home goes through rather than the size of a system: a first unit in the living area, a second room added later, and an old wall unit taken out and replaced.
One and two-bedroom homes make up 77.8% of Collingwood dwellings in the ABS 2021 Census, against 24.2% across Victoria, so a single wall split in the living area is the first install for a large share of homes here. A reverse cycle split covers both seasons in that room: Mitsubishi Electric notes that most split systems heat as well as cool. That matters in a rental, because Consumer Affairs Victoria requires a fixed heater in good working order in the main living area, and an energy efficient one for agreements entered into from 29 March 2023. The wall decides where the indoor unit goes. Mitsubishi Electric's MSZ-AP installation manual asks for a rigid wall without vibration, a fixing height of 1.8 m to 2.3 m above the floor, a position where warm or cool air reaches the whole room, and space to slide the filter out. It calls for a 65 mm hole through the wall that falls 5 to 7 mm towards the outside, so condensate drains away from the room. In a flat, the outdoor unit's position needs more checking than the indoor one, and the site and paperwork sections further down deal with it.
Two-bedroom homes are the largest single group in Collingwood, at 49.9% of dwellings (ABS 2021), which makes the bedroom the natural second room. There are two ways to add it. A second wall split brings its own outdoor unit. A two-head multi-split puts both indoor units on one outdoor unit: Mitsubishi Electric says that design takes up less space outside, and its MXZ-2F52 has 2 ports at 5.2 kW. The shared outdoor unit is also where the trade-offs sit. Mitsubishi's buying guide says every indoor unit on the same outdoor unit must run in the same mode, either heating or cooling, and the capacity is shared between the heads running at the time. Two separate splits each run in their own mode, and as a general rule a fault on one leaves the other room working. As a general rule too, a single split's outdoor unit cannot take a second head, so a multi-split normally means a new outdoor unit. Climate Control Solutions, a Melbourne installer, compares the two options on price, and those figures sit in the prices section below. The decision comes down to the room on the balcony or in the courtyard and whether the two rooms ever need different modes at once.
A replacement starts with getting the refrigerant out of the old unit. The Australian Refrigeration Council says any person who handles refrigerant or works on refrigeration and air conditioning equipment must hold a refrigerant handling licence, and that covers installing, commissioning, servicing or maintaining equipment whether or not refrigerant is present. The ARC and AIRAH refrigerant handling code of practice (2025) says refrigerant must be weighed into and weighed out of a system, so the old charge is recovered and accounted for, not released. Older wall units may run on R22. The ARC says imports of that refrigerant were largely phased out in 2016, that a small allowance can service equipment until 2029, and that an R22 system in good working order does not need to be changed over. When an old unit does fail, The Quote Yard's rule of thumb is that a repair costing more than about half the price of a new system, on a unit past about ten years old, points to replacement. Current models such as Mitsubishi Electric's MSZ-AP series run on R32. The removal itself has a price, and it is listed with the install figures below.
Collingwood is one of Melbourne's oldest suburbs. Wikipedia says land subdivision began in 1838 and was mostly complete by the 1850s, that the gold rush brought a large number of small dwellings, and that large commercial buildings have long sat beside small workers' homes, with many nineteenth century dwellings, shops and factories still in use. That mix sets the install conditions. The three H3s below cover the tight lot, the narrow street outside it and the solid walls of a converted factory.
Wikipedia describes older single and double storey former workers cottages on small subdivisions. On a lot with no side passage, the outdoor unit has three possible places: the rear courtyard, the rear wall or the roof, and the choice between them is made at the inspection, not by a fixed rule. Mitsubishi Electric's MSZ-AP manual sets conditions any position has to meet: good airflow, a rigid wall or support, the unit level, its legs secured if it sits high, and a spot where neighbours are not annoyed by its sound or by hot or cool air. Its clearance diagram runs from 100 mm on the tightest sides to 350 mm on the widest, with open space above, and the pipe between the indoor and outdoor units can be up to 20 m long with a 12 m height difference on these models. A unit across a narrow yard from a neighbour's window also has EPA Victoria's hours to respect: used for heating, it is prohibited on weekdays before 7 am and after 10 pm, and used for cooling, after 11 pm. The rear position has a planning side as well. Yarra's July 2014 heritage permit-exemption plan exempts an air conditioner on a residential building in a heritage overlay when it sits on the rear wall or within the rear setback, or on a side wall set back at least 4 m from the front facade (2 m for a not contributory building), and the exemption does not cover corner properties. A newer plan may apply, so the owner confirms with Yarra City Council before the unit goes on.
Wikipedia says the roads within Collingwood are mainly narrow one-way streets, with Wellington and Langridge Streets among the main arterials. It adds that separated north-south cycling lanes began going in on Wellington Street in 2013, and that the northern half of the suburb moved to 30 km/h speed limits in 2018. The Quote Yard's repairs guide notes that inner-city attendance involves parking difficulty and slow travel between jobs, which businesses build into their fees. So access is planned at the inspection rather than on the day: which way the van approaches along a one-way street, where it can stop, how far the outdoor unit and the recovery cylinder from an old unit have to be carried, whether the building has a lift or only stairs, and whether a roof position needs ladders or other access equipment. Mr Duct Cleaning notes that a unit high on a second-storey wall or on a roof needs extra equipment, a point that applies to fitting a unit as much as to cleaning one. Parking restrictions and permits vary by street and are checked with the council for the address; this page quotes no parking rule. In an apartment block, the owners corporation or building manager may set rules for lift bookings and loading, and those go into the booking too.
Wikipedia says Oxford and Cambridge Streets are dominated by imposing red-brick factories and warehouses, formerly occupied by Foy & Gibson, and that older warehouses and factories across the suburb have been converted into apartments. In a conversion with solid brick walls and a concrete ceiling there may be no cavity to hide pipes in, and as a general rule the refrigerant pipes, drain and cable then run on the surface inside a cover. Mitsubishi Electric's MSZ-AP manual sets what that run needs: copper pipe with 8 mm insulation, bends of at least 100 mm radius, joints covered, the drain hose below the refrigerant pipes and pointing downward, and extra insulation where piping passes through warm, humid spaces to stop condensation. An extension drain hose that crosses a room is wrapped in insulation too. The wall hole is the same 65 mm, drilled through the brick and falling to the outside. A cover run is planned along the line of the brickwork so it reads as part of the room, and the route is drawn on the quote before any drilling, because a hole in solid masonry cannot be moved later. Where the cover and the outdoor unit sit on a shared external wall of the building, the owners corporation's approval is part of the paperwork covered further down.


Flats, apartments and attached homes make up 93.8% of Collingwood dwellings in the ABS 2021 Census, and 64.3% of homes are rented, so an install can need the approval of an owners corporation, a landlord or both before work starts. The three H3s below cover what Peak Air Conditioning Richmond supplies for that: the paperwork that goes with the quote, the licences the work is done under, and the hours the phone is answered.
Consumer Affairs Victoria's model rules for owners corporations apply wherever an owners corporation has not made its own rule on the same item. Rule 4.3(1) says an owner or occupier must not damage or alter common property without the owners corporation's written approval, and rule 5.2(1) says written approval is needed before changing the external appearance of a lot. Rule 5.2(2) says approval cannot be unreasonably withheld, but can carry reasonable conditions to protect other owners' quiet enjoyment, structural integrity or the value of other lots. An outdoor unit on a balcony, a hole through an external wall or a pipe cover on a facade can all fall under those rules. So the written quote is set out to go straight to the committee or building manager: the indoor and outdoor unit models and capacity, where the outdoor unit sits, the pipe and drain route, where the wall is drilled and the cover used. For a rented flat, the same document goes to the agent and the landlord, who approves the work. The quote follows an inspection because those positions are measured on site, not guessed from a floor plan.
Two kinds of licensed work sit inside a split system install. The refrigerant side needs a refrigerant handling licence from the Australian Refrigeration Council, and Mitsubishi Electric's MSZ-AP manual says only ARC-licensed technicians should install the product. The electrical side needs a licensed electrician: the same manual says the wiring between the indoor and outdoor units must be installed by a licensed electrical contractor to meet AS/NZS 3000. Energy Safe Victoria says a Certificate of Electrical Safety is required by the Electricity Safety Act 1998, and that the electrician must give the customer a copy within 30 days for non-prescribed work, or within 4 days of completing the certificate for prescribed work, which must also be inspected by a licensed electrical inspector. Each install is carried out under the licence its trade requires, and the certificate is a document worth keeping with the owners corporation or agent file, next to the service records. A manufacturer warranty applies when the unit is installed to the manufacturer's requirements, which is one more reason the paperwork names the model and the installer's details.
The phone line is answered from 6am to 10pm every day, Saturdays and Sundays included. That suits the people who arrange work on a rented flat: a landlord or agent can call outside office hours, and a tenant reporting a fault rings the same number. For repair visits, Consumer Affairs Victoria says a rental provider must give at least a full day's notice of entry and enter only between 8am and 6pm on any day except a public holiday, though a renter may agree to other times for an urgent repair, so the visit time is set with the tenant when the job is booked. QuickAir names March and April as the easy months to book heating work, September and October for cooling, and says the first cold snap in May and the first serious heatwave in December fill the diary. Booking in the quieter months gives the widest choice of days. The line is not staffed between 10pm and 6am, and no attendance time is promised on the call: it is agreed when the job is booked.
Wikipedia bounds Collingwood by Smith Street to the west, Alexandra Parade to the north, Hoddle Street to the east and Victoria Parade to the south. Inside those lines the land use changes from block to block, and so does the job: shops and offices along Smith Street and in the south, rows of older houses in the north, and small parks between factories and terraces. The City of Yarra's Database of Heritage Significant Areas (March 2024), read for this page, grades every address in a heritage overlay, and those gradings are summarised below by street, never for a single house.
Smith Street became the dominant shopping strip in the 1870s and had its tram line from 1887, and Wikipedia calls it one of Melbourne's major nightlife and retail strips, named the coolest street in the world in 2021. Its Collingwood side sits mainly in heritage overlay HO333, where the database lists 157 rows, 76 of them shops and residences: 83 graded contributory, 28 individually significant and 43 not contributory. Yarra's permit-exemption plan covers residential buildings and uses only, and the council says a planning permit is normally required for works in a heritage overlay, so a unit for a shop is checked with the council first. South of the strip, Wikipedia says the office sector has grown through developments in the suburb's southern former industrial area. No source records which plant each building runs, so the system is chosen at the site. Mitsubishi Electric describes its PKA-M wall units for offices, meeting rooms and retail spaces, its SUZ-M outdoor units as particularly suited to shop front installations, and its under-ceiling units for shops with exposed ceilings or heritage features where ducted systems are not viable. whatsthedamage's commercial guide adds building management approval, after-hours work and noise limits near neighbours to the cost drivers. Commercial air conditioning covers office and shop systems in full.
Wikipedia places Easey Street in northern Collingwood and Bendigo Street in the north-east. OpenStreetMap shows Easey Street running east-west across the north of the suburb, and Bendigo Street as a short street running north to Alexandra Parade, the northern boundary. Both sit in heritage overlay HO321. Of Easey Street's 84 rows in that overlay, 55 are graded contributory, 19 not contributory and 10 individually significant, most dated 1870 to 1890 or 1900 to 1915, with later flats and a townhouse among the not contributory entries. Bendigo Street has 27 rows: 15 contributory, dated from 1870 to 1925, and 12 not contributory, including three blocks of flats dated 1950 to 1970. Those gradings decide where an outdoor unit can go without a permit. Under Yarra's 2014 exemption plan, a side-wall unit on a contributory or individually significant house has to sit at least 4 m back from the front facade to fall within the exemption, against 2 m for a not contributory building, while a rear wall position is within it for every grading, corner properties aside. The blocks of flats bring owners corporation rules into play as well. An owner can look up a property's grading in the council's database, or ask Yarra City Council, before a wall is chosen.
OpenStreetMap places these three small parks within about 220 m of each other in the south of the suburb, between Smith Street and Wellington Street: Peel Street Park on Peel Street beside Little Oxford Street, Cambridge Street Reserve at 96-98 Cambridge Street, and Oxford Street Park further south on Oxford Street. The streets around them sit mainly in heritage overlay HO318. Peel Street's 24 rows there include shops and residences graded individually significant, factory and warehouse buildings from the 1930s graded contributory, and later offices graded not contributory. On Oxford Street the former Foy & Gibson warehouse, powerhouse and woollen mills buildings are on the Victorian Heritage Register, and most of Cambridge Street's terraces sit in a second overlay, HO336. Two points follow for an install near the parks. Yarra's exemption plan applies its conditions to a unit visible from a street or a public park, so a wall facing one of these parks is treated like a street-facing wall. And the plan does not apply to places on the Victorian Heritage Register; Yarra City Council says Heritage Victoria decides applications for registered places, so a unit on one of those buildings goes through that process first.


The Australian Government's Energy Rating site notes that air conditioners can also be known as heat pumps, and a reverse cycle model is the type that heats. For a Collingwood flat that still runs an old gas wall heater, the Victorian Energy Upgrades program lists a discount of up to $1,610, and bill savings of up to $460 a year, for replacing a non-ducted gas space heater with an efficient reverse cycle air conditioner (energy.vic.gov.au, updated 29 October 2026). Reverse cycle air conditioning is set out in full on its own page. YourHome describes hydronic heating, hot water through radiator panels or under the floor, as a separate system that is typically dearer to buy and install than space heaters. The two H3s below split by the space being heated: a tall single room in a converted warehouse, and a townhouse over more than one level.
Wikipedia records that older Collingwood warehouses and factories have been converted into apartments. Where a conversion keeps a tall original ceiling, the room holds more air than its floor area suggests, and Mitsubishi Electric's buying guide says so directly: taller ceilings mean more air volume to cool or heat. The same guide says sizing is not as simple as square metres and calls for a heat load calculation that weighs ceiling height, insulation, the size and orientation of windows and which sides face the sun. For heating, the figure to compare is on the Zoned Energy Rating Label, which shows heating capacity at two outdoor temperatures and cooling at only one; the Energy Rating site says the higher the kW value, the more heating the unit delivers at that temperature. Mitsubishi Electric's MSZ-AP wall splits run from 2.5 kW to 7.8 kW and list heating operation down to minus 15 °C outside, and Daikin markets its XL Series for large open-plan living. A high wall unit is not the only layout for a tall room. YourHome notes that warm air naturally rises and suggests a mix of radiant and convective heating in larger rooms with high ceilings, and Daikin says a floor standing unit, mounted lower, warms the ground more effectively. Where the building is a heritage building, Yarra City Council's energy efficiency guide says most were built without insulation and with single glazing, and lists blocking draughts first. As a general approach, the heat load is worked out on the room as it will be once any such work is done.
Semi-detached, row and terrace houses and townhouses make up 25.6% of Collingwood dwellings (ABS 2021), and Wikipedia notes modern townhouse infill among the newer housing. For a townhouse with rooms on more than one level, ducted reverse cycle is a single system that heats in winter and cools in summer through the same ducts. YourHome, the Australian Government's guide, says ducted air heaters can run on gas or electricity and that electric systems may also be used for cooling, but that ducts need to be larger if they also cool, and that each outlet needs a return air path back to the central return, such as a gap under the door. Zoning lets the system serve only the level in use. Mitsubishi Electric's ducted page says its Zone Controller creates up to 4 or 8 zones, while its May 2026 brochure lists 4-zone and 10-zone models with on/off or linear damper control. Where the ceiling space is shallow, Mitsubishi's PEAD bulkhead series stands 250 mm high. Where a townhouse already has gas ducted heating, the Victorian Energy Upgrades table lists up to $2,520 off a 10 kW ducted reverse cycle replacement, up to $4,200 at 16 kW and up to $5,530 at 22.4 kW, with bill savings of up to $1,140 a year. Seeley International says its Braemar Dominator Series 2 fits into the ceiling space to directly replace an existing gas heater unit.
Rented homes are 64.3% of Collingwood dwellings in the ABS 2021 Census, more than double the Victorian share of 28.5%, so servicing here is often booked by a landlord or an agent, and faults are often reported by a tenant. The three H3s below follow that workflow: routine servicing and cleaning on the landlord's schedule, the two-yearly gas ducted heater check, and breakdowns a tenant reports. Evaporative coolers are not among the services offered here, so this page does not cover them; the work below is on refrigerated split, multi-head and ducted systems and on gas ducted heaters.
The Quote Yard calls annual servicing the sensible default for a domestic system in Victoria, and QuickAir, a Melbourne installer, says once a year suits most Melbourne homes because a reverse cycle system carries the house through winter as well as summer. Neither is a regulation, and the unit's own manual comes first. QuickAir lists what a full service covers: an indoor coil clean, a drain flush, an outdoor unit clean, operating checks and a refrigerant assessment. For a landlord or agent the record matters as much as the visit, and The Quote Yard says a service record should contain more than a receipt for payment. Aircon cleaning is a different job from a service. Mr Duct Cleaning, a Melbourne cleaner, describes a full clean: drop sheets down and a wash bag fitted under the unit, filters washed, the coil and fins foamed and brushed, the barrel fan scrubbed by hand, a low-pressure rinse into the bag, and the outdoor unit cleared of leaves, dust and cobwebs. It says the coil and barrel fan are the parts that grow mould and cause a musty smell, and that a clean is not a service, because regassing and repairs need an ARC licensed technician. The steps are on the aircon cleaning page. Booking the clean and the service for the same visit means the tenant arranges access once.
Energy Safe Victoria recommends that all gas heaters are serviced at least every two years by a qualified gasfitter, who checks the installation and tests for carbon monoxide leakage. A rented home carries a second duty alongside it: Consumer Affairs Victoria requires a gas safety check every 2 years by a gasfitter registered with the Building and Plumbing Commission and endorsed for Type A gas appliance servicing. The BPC says gas servicing must follow AS 4575, with the Appendix E checklist that includes carbon monoxide testing, and that the customer receives the complete servicing record within 5 days. It adds that a rental provider must give the renter a copy of the gas safety check within 7 days on request, so the agent's file needs one. This part of the job is done by a licensed gasfitter, not by an air conditioning technician. Duct cleaning is a separate job with its own interval. The Quote Yard lists duct cleaning as separate from a system service. Mr Duct Cleaning says a duct clean covers the supply and return air ducts, registers, grilles, fans and the air handling unit, using high-powered vacuums and air-pressure tools, and gives every 3 to 5 years as a rule of thumb, sooner with musty odours, visible dust around the vents or after renovation work. Paired with the two-yearly heater service, a duct clean at every second visit comes round about every four years, inside that window, or earlier if those signs appear.
Consumer Affairs Victoria lists a cooling appliance or service provided by the rental provider that is not working as an urgent repair, alongside heating that is not working, and says the rental provider must make urgent repairs without delay. The renter reports the fault in writing, or through the emergency number given at the start of the tenancy and then in writing. Fault finding starts with simple checks. Daikin's troubleshooting guide lists the mode and set temperature, clean filters, nothing blocking the unit, the breaker, and closed windows and doors. It also notes two normal behaviours that look like faults: a restart delay of about 3 minutes, and a heating pause of about 3 to 10 minutes while the outdoor unit defrosts. Where the cause is refrigerant, the order of work is fixed. The Quote Yard says a sealed system does not consume refrigerant, so a low charge means a leak, found with an electronic detector, ultraviolet dye or a nitrogen pressure test. The ARC and AIRAH code of practice says a system known to be leaking must not be topped up until the leaks are fixed, and that it is recharged to the quantity on its identification plate. A flare joint at the outdoor unit is quick to remake, while a leaking coil often means a new coil. Air conditioning repair covers each fault in more detail.


The figures below are indicative ranges from Melbourne cost guides and installers, not the business's own prices. Each job is priced in a written quote after an inspection, because pipe length, access and electrical work only show up on site.
whatsthedamage's Melbourne table (updated November 2026) puts a supplied and installed split at $1,250 to $2,625 for 2.5 kW and $1,475 to $2,950 for 3.5 kW, and install-only, with the unit supplied by the customer, at $735 to $1,575. Climate Control Solutions, a Melbourne installer, puts a 3.5 kW back-to-back job, with the outdoor unit on the other side of the same wall, at around $2,100 to $2,600. Three items move a Collingwood quote away from that. Pipe run length: a run to a rear courtyard or a roof adds pipe, insulation, covers and labour, and on the MSZ-AP models anything beyond the pre-charged length (10 m on the smaller sizes) needs extra refrigerant at 20 g/m. Old unit removal: Climate Control Solutions adds about $250 per unit, and whatsthedamage gives $105 to $370 for removal and disposal, or $1,575 to $3,150 for a full like-for-like changeover. A new circuit: Climate Control Solutions allows roughly $450 for the licensed electrical work. Each of these is itemised on the air conditioning installation page.
For two rooms, Climate Control Solutions says two separate 3.5 kW splits run about $4,600 to $5,800 installed, while a 2-head multi-head system lands around $4,000 to $5,200. whatsthedamage's Melbourne table gives $4,200 to $7,900 for 2 heads ($5,800 typical) and $7,350 to $12,600 for 4 heads ($8,900 typical); each extra head adds an indoor unit, a pipe run and a drain. For ducted, QuickAir puts a small 1 to 2-bedroom home at $5,000 to $8,000. whatsthedamage prices a 3-bedroom home, or a single-storey 4-bedroom with good roof access, at $8,400 to $14,700 ($11,550 typical), and places two-storey or room-by-room zoned systems in its premium band at $12,600 to $23,100 ($16,800 typical). A multi-level townhouse with a zone on each floor matches that second description. Roof access is written into the guide's own band description, so the inspection checks the ceiling space before a band is set.
whatsthedamage puts an air conditioning service or clean at $105 to $335 per unit in Melbourne ($210 typical), so a flat with a split in the living area and another in the bedroom is priced per unit, not per flat. For a breakdown, The Quote Yard's repairs guide (published 7 September 2026) prices callouts by area, and its Inner Melbourne list, read on 19 November 2026, names Collingwood: the Inner Melbourne & CBD band is $160 to $280 for the callout, with a typical repair total of $400 to $1,200, and the guide says the callout is usually credited against the repair if it goes ahead. The same guide gives $400 to $900 for a leak repair and regas. For the gas side, homeupkeep's Melbourne guide puts a gas ducted heater service with a carbon monoxide test at $280 to $380.

Air Conditioning Installation
Split, multi-head and ducted air conditioning installation across Richmond, sized room by room for terraces, apartments and warehouse conversions, with a free written quote after inspection.

Split System Installation
Split system installation in Richmond for wall, floor console and multi-head units, with the outdoor position, pipe route and kilowatt size set out in a written quote.

Ducted Air Conditioning
Ducted air conditioning for Richmond homes: standard, slimline and underfloor systems, zoned room by room, with an itemised written quote after a roof inspection.

Reverse Cycle Air Conditioning
Reverse cycle air conditioning in Richmond sized for winter heating, with gas heater swaps, VEU discount checks and heating kW set out in a written quote.

Hydronic Heating
Hydronic heating in Richmond: radiator panels, in-slab and underfloor pipes, gas boilers and heat pumps, with servicing and a written quote after inspection.

Air Conditioning Repair
Air conditioning repair in Richmond for split, multi-head and ducted systems, with faults traced to the cause and a written quote before any part is ordered.

Emergency Air Conditioning Repair
Emergency air conditioning repair in Richmond for split and ducted systems, booked from 6am to 10pm, seven days, with the callout price confirmed before a technician is sent.

Air Conditioning Service
Air conditioning service in Richmond for split, multi-head, cassette and ducted systems, with filters, coils, drains, outdoor units and refrigerant pressures checked and a written record left.

Aircon Cleaning
Aircon cleaning in Richmond for wall splits and multi-head systems: filters, coil and barrel fan washed into a wash bag, the outdoor coil cleared and airflow tested afterwards.

Ducted Heating
Ducted heating in Richmond: gas ducted heaters from 3 to 6 stars, electric ducted heat pumps, old heater swaps and a written quote after a heat load check.

Ducted Heating Service and Repairs
Gas ducted heating service in Richmond to AS 4575: burners, heat exchanger and flue cleaned and checked, a CO spillage test, faults traced and repairs quoted in writing.

Commercial Air Conditioning
Commercial air conditioning in Richmond for shops, offices and mixed-use buildings: split, cassette, under-ceiling, ducted, packaged and VRF systems, itemised quotes and maintenance contracts.
air conditioning In Collingwood
Climate Control Solutions, a Melbourne installer, gives indicative installed prices of $1,900 to $2,500 for a 2.5 kW split and $2,300 to $2,900 for 3.5 kW, with a 3.5 kW back-to-back job at around $2,100 to $2,600. In an apartment the common extras are the pipe run to wherever the outdoor unit is allowed to sit, removal of an old unit (about $250 per unit on the same page) and a new circuit (roughly $450). Owners corporation approval adds time rather than a published fee. These are indicative figures, not a quote, and a written quote follows an inspection of the flat.
The Quote Yard's Victorian repairs guide (published 7 September 2026) gives $400 to $900 for a leak repair and regas, and whatsthedamage's Melbourne table puts a major repair or regas at $315 to $1,250 per job. A regas on its own is not the whole job where there is a leak: a sealed system does not use up refrigerant, so a low charge means a leak, and the ARC and AIRAH code of practice says a leaking system must not be topped up until the leak is fixed. The price therefore depends on where the leak is, from a flare joint at the outdoor unit to a coil that has to be replaced. The refrigerant is then weighed in to the figure on the unit's identification plate.
Consumer Affairs Victoria says the rental provider must organise and pay for all repairs that are not the renter's fault, while a renter who caused the damage may have to pay. A cooling appliance or service provided by the rental provider that stops working counts as an urgent repair, as does heating. If there is no prompt response to an urgent repair, the renter can arrange and pay for it, but only where it costs $2,500 or less, and the rental provider must pay them back within 7 days. Work that needs a licence must be done by a qualified person, which for refrigerant means an ARC licence holder.
Energy Safe Victoria recommends that all gas heaters are serviced at least every two years by a qualified gasfitter, with the installation checked and a test for carbon monoxide leakage. Brivis's service manual for its StarPro heaters also sets out its maintenance schedule at two-year intervals. In a rental, Consumer Affairs Victoria separately requires a gas safety check every 2 years. The service follows AS 4575, and the Building and Plumbing Commission says the customer receives the completed servicing record within 5 days.
No independent ranking settles it, and sizing and installation decide more of the result than the badge: YourHome stresses getting the system the right size for the house, with duct runs straight and all joints tightly taped. The makers differ in the details. Mitsubishi Electric's May 2026 brochure lists Zone Controllers in 4-zone and 10-zone models, Daikin says most of its ducted systems use R-32 and can last 10 to 15 years or more with care, and Seeley International's Braemar range includes ducted reverse cycle systems. Daikin also cites being voted the most trusted air conditioner brand in a Reader's Digest Australia survey from 2023 to 2026, which is a brand claim rather than a performance test. The choice is made at the quote, against the home's ceiling space and zones.
It can, where the space meets the manufacturer's clearances and the building's rules. Mitsubishi Electric's MSZ-AP manual shows clearances from 100 mm on the tightest sides to 350 mm on the widest, with open space above, and asks for good airflow, a level and rigid base, and a spot where neighbours are not bothered by its sound or air. On an apartment balcony, Consumer Affairs Victoria's model rule 5.2 requires the owners corporation's written approval before the external appearance of a lot is changed, where the corporation has no rule of its own. EPA Victoria's noise rules apply too: a unit used for cooling is prohibited on weekdays before 7 am and after 11 pm if it can be heard in a habitable room of another home. Peak Air Conditioning Richmond checks the space at the inspection before a model is chosen.
GET A FREE QUOTE
BUSINESS
SERVICES
OPERATING HOURS
Sun: 6:00am - 10:00pm
Mon: 6:00am - 10:00pm
Tue: 6:00am - 10:00pm
Wed: 6:00am - 10:00pm
Thu: 6:00am - 10:00pm
Fri: 6:00am - 10:00pm
Sat: 6:00am - 10:00pm