Hydronic Heating Richmond, Radiant Warmth Without Blown Air

Hydronic heating Richmond households choose warms rooms with hot water rather than blown air. A gas boiler or an electric heat pump heats the water, and a pump sends it through radiator panels on the walls or through pipes laid in a slab or under the floor. The Australian Government's energy.gov.au describes hydronic radiant systems as silent in operation, with high purchase and installation costs. Richmond's homes run from single-fronted Victorian houses on long, thin blocks to apartments, and the ABS 2021 Census counts 54.7% of dwellings as rented, so a job often involves an owner, agent and tenant. Peak Air Conditioning Richmond plans new systems room by room, has gas boiler work done by a licensed gasfitter registered with the Building and Plumbing Commission, and services, bleeds and repairs existing systems. Bookings run from 6am to 10pm, seven days. Call 0468 046 042 to arrange an inspection.

GET A FREE QUOTE

Why Choose Peak Air Conditioning Richmond for Heating and Cooling for Hydronic Heating

Peak Air Conditioning Richmond installs, repairs, services and cleans heating and cooling systems across Richmond and 12 nearby suburbs. Two things set out what a buyer gets before any work is booked: a written quote that itemises the job, and one phone line that covers all 12 services from 6am to 10pm. Each trade's work is done under the licence it requires: an ARC refrigerant handling licence for refrigerant work, a licensed gasfitter registered with the Building and Plumbing Commission for gas work, and a licensed electrician, who issues a Certificate of Electrical Safety, for wiring.

Peak Air Conditioning Richmond

Hydronic Heating Richmond: Radiator Panels, In-Slab and Underfloor Systems

YourHome, the Australian Government's guide to sustainable homes, describes hydronic systems as ones that circulate hot or cold water or other fluid through radiator panels in rooms or under the floor. That gives three ways for the heat to reach a room, and the choice between them depends on whether the floor already exists, how much wall space is free and how the home is used. The heat source, a gas boiler or a heat pump, is a separate decision covered further down this page.

Wall-Mounted Radiator Panels

A radiator panel is a flat metal emitter fixed to a wall, with hot water entering through a valve on one side and leaving through a second valve on the other. Daikin's Altherma brochure calls radiators a more traditional and cost-effective heating solution, often wall-mounted, and lists them beside underfloor circuits and fan coil units as one of three emitter types a hydronic heat source can drive. In Bosch's installation manual for its Condens 5000W boiler, the valve on the flow side is the radiator valve and the valve on the return side is a lockshield valve, which is set once to control how much water that panel receives. Panels suit an existing home, because the floor stays as it is and only pipes need to reach each room. The Quote Yard's Victorian hydronic guide makes the same point against ducted heating: hydronic needs only small pipes, where a ducted system needs room for large ducts.

In-Slab Pipes for New Floors and Extensions

In-slab heating sets the pipework inside a concrete floor, and energy.gov.au lists piping in a concrete slab as one of the two forms a hydronic radiant system takes. Because the pipe is cast into the concrete, the decision has to be made before the slab is poured. That is why in-slab heating fits a new ground floor, a rear extension or a knock-down rebuild rather than an existing room. The same government page advises seeking expert advice before a major investment such as an in-slab system, since the pipe cannot be reached once the concrete has set. Daikin describes underfloor heating as running low-temperature water through the floor pipes, and notes that tiles and stone conduct heat better than other finishes, so the finished floor covering belongs in the plan from the start. For a Richmond renovation that adds a slab-on-ground kitchen and living area at the back of a terrace, this is the stage at which the pipe layout and the floor finish are decided together.

Underfloor Pipework Beneath Suspended Timber Floors

Where a house sits on a suspended timber floor with a crawl space beneath, hydronic pipework can be run under the boards instead of in a slab, heating the room from below. Daikin's underfloor heating guidance says timber and carpet may require specific installation considerations, which is why the fixing and insulation method is taken from the floor-heating system maker's instructions and confirmed at the inspection rather than assumed. Temperature control matters on this kind of floor: Bosch's boiler manual requires plastic underfloor pipework to be controlled by a thermostatic blending valve that limits the circuit temperature to approximately 50 °C, and requires at least 600 mm of copper pipe at the boiler where plastic pipe with a polymeric barrier is used. Whether a particular Richmond house has enough clearance under the floor to work in is something only a look through the subfloor access can settle, so the quote states it after that check.

Clifton Hill Emergency Air Conditioning Repair
Carlton Emergency Air Conditioning Repair

Peak Air Conditioning Richmond

Hydronic Heating Installation Planned from Heat Loss to Controls

A hydronic installation is planned in a fixed order: how much heat each room loses, how the pipes will reach each emitter, how heat is kept in the pipes and walls, and how the system is controlled once it runs. Each step below feeds the next, and the written quote is built from the result.

Room-by-Room Heat Loss and Panel Sizing

Each room is assessed on its own, because a front bedroom, a rear living area and an upstairs room lose heat at different rates. The factors are the floor area and ceiling height, the insulation in the roof, walls and floor, the size and glazing of the windows, and the draughts around doors and windows. Energy.gov.au notes that gap sealing, insulation and double glazing all reduce heating loads, so a room that is draught-proofed first may need less emitter capacity. As a general rule of how hydronic emitters work, a panel gives off more heat when the water running through it is hotter, so panel sizes are matched to the water temperature of the chosen heat source as well as to the room. The total of all rooms then has to sit within the heat source's rated output. For scale, Daikin's Altherma Mono-Bloc brochure lists rated heating capacities from 9.37 kW to 16 kW, and Bosch's Condens 5000W is an 18 kW boiler. No sizing table is used here: the heat-loss result for the actual house sets the number and size of panels.

Pipe Routes Through the Subfloor and Walls of Existing Terraces

Wikipedia's entry for Richmond says most of the suburb's houses are single-fronted Victorian style houses built from the 1850s to the 1930s, typically on long, thin blocks with two bedrooms at the front and the family room and kitchen at the back. In a layout like that, flow and return pipes have to travel the length of the house to reach the front bedrooms. Where the floor is suspended timber, the subfloor can be the shortest route, with a short rise through the floor or wall to each panel. Where it is not, pipes run in walls or along skirtings. The Quote Yard's guide notes that running small pipes through a solid brick wall is far less invasive than cutting duct routes. The route also has rules of its own: Bosch's manual requires a drain point at the lowest part of the system and an air vent at all the high points, so a route that rises and falls over joists or doorways needs more vents than a level one.

Insulated Pipework and Insulated Walls Behind Panels

Heat lost on the way to a room is heat paid for but never felt. YourHome advises that water circulation pipes are well insulated, and states that exterior walls behind panels must also be well insulated. The pipe point is simple: an uninsulated run under a draughty timber floor gives up warmth to the subfloor before the water reaches the front of the house. The wall point is less obvious. A panel fixed to an outside wall warms the wall behind it as well as the room in front, so an uninsulated external wall draws part of that panel's output straight outdoors. Energy.gov.au lists roof, wall and floor insulation among the simple ways to reduce heating loads. In an existing brick home, insulating a solid wall can be impractical, so placing a panel on an internal wall where the layout allows is weighed room by room at the inspection.

Zone Valves, Thermostats and Smart Pump Controls

Controls decide how much of the house is heated and for how long. YourHome recommends smart controls to manage pump usage, and The Quote Yard's guide explains why: older fixed-speed pumps run flat out whenever the system calls for heat, while variable-speed pumps adjust to demand. At the panel, Bosch recommends thermostatic radiator valves on every radiator in the sleeping rooms, but not on the radiator in the room where the main room thermostat sits, so that the thermostat reads a true temperature. Zone valves split the house into areas, such as bedrooms and living space, that run on separate timers. Bosch also says an external automatic bypass should be fitted where zone valves and thermostatic valves can significantly reduce or stop the system flow, which protects the boiler and pump. On the heat pump side, Daikin's Altherma controller can set the water temperature of up to two zones or emitters separately, which suits a house that has radiators in one part and an underfloor circuit in another.

Peak Air Conditioning Richmond

Why Choose Peak Air Conditioning Richmond for Hydronic Heating

A hydronic system can involve two regulated trades as well as the pipework: gasfitting for a boiler, and electrical work for pumps, controls and heat pumps. Peak Air Conditioning Richmond has each part done under the licence it requires, and sets out in writing what the job covers before work starts. Inspections can be booked from 6am to 10pm, seven days, with same-day visits where possible. With 54.7% of Richmond dwellings rented (ABS 2021 Census), early and evening times often suit a property manager arranging access around a tenant.

Gas Boiler Work Only by a Licensed Gasfitter Registered with the BPC

Energy Safe Victoria's advice to householders is plain: always use a licensed gasfitter for any installation, repair or renovation that involves gas. Consumer Affairs Victoria explains that a registered or licensed gasfitter is a plumber who holds registration or a licence with the Building and Plumbing Commission to carry out gasfitting work. Installing or replacing a gas boiler is that kind of work. The Building and Plumbing Commission states that a compliance certificate must be issued for the installation, relocation or replacement of any Type A gas-using appliance, regardless of the cost, and for installing or modifying consumer gas piping. The certificate must be given to the customer within five days of completing the work and lodged with the Commission in the same period. Bosch's manual adds the technical side: its gas boilers must be installed by an authorised person in accordance with AS/NZS 5601 and AS/NZS 3000, and the gas supply pipe must never be smaller than the boiler's inlet. A homeowner can ask to see the gasfitter's registration before work begins.

A Written Quote Itemising Panels, Pipe Runs and the Heat Source

A hydronic price cannot be fixed over the phone, because it depends on what the heat-loss check and the subfloor inspection find. The written quote that follows the inspection lists each room's emitter: the number and size of radiator panels, or the floor circuit and its manifold. It names the pipe route and how the pipes are insulated, the heat source by type and rated output, and the controls, including zones and thermostatic valves. Daikin notes that heat emitters are supplied separately from its heat pump, so the panels and the heat source appear as separate lines rather than one bundled figure. Where an existing system is being reconnected to a new heat source, the quote states whether a flush and fresh inhibitor are included. It also lists the paperwork due at the end: the gas compliance certificate for a boiler and the Certificate of Electrical Safety for new wiring. In a rental, the quote goes to whoever authorises the work, usually the owner through the managing agent.

A Certificate of Electrical Safety for Heat Pump and Pump Wiring

Even a gas boiler runs on electricity. Bosch lists a 240 V supply, a maximum power consumption of 140 W and an external 3 A fuse for its Condens 5000W, and states that the boiler must be earthed and wired to AS/NZS 3000. A heat pump draws far more: Daikin lists a rated heating input of 1.91 to 3.53 kW for its Altherma Mono-Bloc, which runs on a single-phase 230 V supply, and carries a 3 kW electric booster heater for very cold weather. Where new electrical installation work is done to supply a heat pump, a boiler, pumps or controllers, Energy Safe Victoria says a Certificate of Electrical Safety is required by the Electricity Safety Act 1998, and the registered electrical contractor or licensed electrical worker must give the customer a copy, within 30 days for non-prescribed work. The Quote Yard's Victorian guide makes the same point for repairs: electrical connections require a licensed electrical worker. The certificate is worth keeping with the system's papers, because Victorian rental providers must also have electrical installations checked by a licensed or registered electrician every 2 years.

Abbotsford Emergency Air Conditioning Repair
Carlton Emergency Air Conditioning Repair

Peak Air Conditioning Richmond

What Hydronic Heating Costs in Richmond

The service and repair figures below come from The Quote Yard's Victorian hydronic repairs guide, published 10 September 2026. They are the site's estimates of typical Victorian market rates, not a price list, and a written quote is given after the system has been inspected. No independent cost guide read for this page gives a current installation price for a new hydronic system, so none is quoted here.

Hydronic Heating Installation Cost and What Sets the Quote

Energy.gov.au says the purchase and installation costs of hydronic radiant systems are high, and YourHome describes hydronic heating as typically more expensive to buy and install compared with space heaters. Beyond that, the price of a new system is set by its design. The number and size of panels follow from the room-by-room heat loss, so a larger or draughtier house needs more emitter capacity. The emitter type matters: radiator panels on an existing house, pipes cast in a new slab and pipework under a timber floor are different jobs. The heat source adds its own work, either a gas boiler with its gas pipe, flue and condensate drain, or a heat pump outdoor unit with its electrical supply. Pipe run length and access, through a subfloor, walls or upper floors, drive labour. Zones, thermostatic valves and smart controls add parts, and making good walls and floors after the pipes are in adds finishing work. Each of these is priced line by line in the written quote.

Boiler Service, Bleeding and Balancing Prices

The Quote Yard puts a hydronic boiler service at around $200 to $450 in Victoria, with a written report, and recommends the service annually or every second year. Its guide describes what a service covers: combustion, the heat exchanger, the flue, the safety devices, system pressure and the corrosion inhibitor concentration. Radiator bleeding and system balancing is listed at around $150 to $400, and the guide estimates one to two hours for the job. Bleeding releases trapped air, while balancing sets the lockshield valve on each panel so that rooms far from the boiler receive enough flow. The guide notes that balancing is charged as labour because it is a skill rather than a part. It also warns that repeated air means a leak, so a system that needs bleeding every few weeks points to a repair, priced in the next section, rather than another bleed.

Repair Prices: Pumps, Valves, Power Flushes and Boiler Replacement

For repairs, The Quote Yard lists expansion vessel or relief valve replacement at around $350 to $900, and calls it a common cause of pressure loss. Its guide adds that some expansion vessels can be recharged rather than replaced, so the cheaper fix is checked first. A circulating pump replacement is listed at $450 to $1,200, a power flush and system clean at $700 to $2,200, and a full boiler replacement at $6,000 to $16,000. The flush price depends mainly on how many radiators are involved and how contaminated the system is, and the guide advises that a flush comes before a new boiler is fitted. These figures vary with system size and age, the number of radiators or zones, the boiler brand and parts availability, and whether the system is gas fired, electric or heat pump. Boiler replacement is a repair-side figure for swapping a boiler on an existing system; it is not the price of a new hydronic installation.

Peak Air Conditioning Richmond

Hydronic Heating versus Ducted Gas and Reverse Cycle Heating

Energy.gov.au lists ducted gas heating and electric reverse cycle air conditioners beside hydronic heating among household heating choices. The two alternatives are gas ducted heating that blows warm air through ducts, and a reverse cycle air conditioning system that heats and cools with an air-to-air heat pump. The three systems differ in how the heat feels, what they cost to buy and run, and what they ask of the home.

Radiant Warmth versus Forced Air: Draughts and Noise

YourHome describes ducted air heaters as circulating hot air through roof or underfloor ducts, supplying convective heat. A hydronic panel or floor warms the room differently, giving off radiant heat from its surface as well as warming the air around it. Daikin's Altherma brochure, from a maker that sells both kinds of system, says conventional air conditioning may create draughts and dry out the air, while hydronic heating radiates the heat evenly rather than blowing hot air through the home. On noise, energy.gov.au says the operation of hydronic radiant systems is silent and that they do not distribute dust particles. That applies inside the rooms: the heat source still makes some sound. Bosch lists 42 dBA as the maximum central heating noise output of its indoor boiler, and Daikin lists a 62 dBA sound power level for its Altherma outdoor unit when heating. YourHome adds that in larger rooms with high ceilings a combination of radiant and convective heating is best.

Upfront Price and Running Costs Against Other Heating

On upfront price, hydronic heating sits at the expensive end: energy.gov.au calls its purchase and installation costs high, and says ducted gas purchase, installation and running costs can also be costly. Running costs depend on the heat source more than the emitters. Energy.gov.au says hydronic running costs are lower when the system is powered by solar or electric heat pumps, and describes ducted gas heating as expensive to operate due to significant gas consumption and electricity for the fans. Daikin's brochure states that its Altherma heat pump needs 1 kW of electrical energy to release more than 4 kW of heat, and lists rated heating efficiencies (COP) of 4.53 to 4.91 across the range. Energy.gov.au gives reverse cycle air conditioners an efficiency of 300% to 600%. A gas boiler burns gas and also uses electricity for its pump and controls. No independent source read for this page gives a dollar running cost for hydronic heating, so the actual bill depends on the tariff, the insulation and the hours the system runs.

The Downsides of Hydronic Heating: Warm-Up Time and Panel Wall Space

Hydronic heating is slower to bring a cold house up to temperature. Daikin's own underfloor guidance says underfloor heating may take slightly longer than conventional heaters to reach the target temperature, and The Quote Yard's guide says a hydronic system takes longer to warm a cold house than ducted air does and costs more upfront. In practice that suits a timer that starts the heating before people get up or come home, rather than switching it on at the moment the room feels cold. Wall space is the second trade-off. Daikin contrasts underfloor heating with wall-mounted heaters and radiators because the floor version is hidden, preserving wall and floor space, which means radiator panels do take wall area that furniture cannot then use. In a narrow single-fronted house, that can limit where a sofa or bookcase goes. A gas boiler system also heats only: YourHome lists gas as a hydronic heat source for systems used for heating only, so summer cooling needs a reverse cycle heat pump or a separate air conditioner.

Abbotsford Emergency Air Conditioning Repair
Carlton Emergency Air Conditioning Repair

Peak Air Conditioning Richmond

Gas Boiler or Heat Pump: Choosing the Hydronic Heat Source

YourHome lists three ways to heat the water in a hydronic system: electric heat pumps, solar collectors, or gas if the system is used for heating only. For a Richmond home the practical choice is between a gas boiler and an air-to-water heat pump, and an existing gas system can be moved from one to the other.

Gas Boilers for Heating-Only Systems

A gas boiler heats the system water by burning natural gas or LPG and sends it round a sealed circuit. Bosch's Condens 5000W, an 18 kW condensing system boiler, shows what that involves: the manual states a maximum flow temperature of 82 °C, a maximum operating pressure of 250 kPa, and that the boiler may only be installed in a sealed, unvented central heating system and is intended for indoor use only. Because it is a condensing boiler it produces condensate, up to 1.5 litres an hour on Bosch's figures, and its condensate pipe must be at least 40 mm plastic and fall at least 50 mm per metre towards the outlet, so the boiler's position is chosen with a drain route in mind. With an optional diverter valve, the same boiler can also heat a hot water cylinder, to a maximum of 75 °C. Energy.gov.au notes that gas heaters lose heat through the flue and use electricity for fans and other parts, which is why boiler efficiency varies with its design. A boiler gives no cooling, which is the trade-off against a reversible heat pump.

Air-to-Water Heat Pumps That Heat and Can Also Cool

An air-to-water heat pump uses the same refrigeration cycle as an air conditioner, but heats water instead of air. Daikin describes its Altherma as an air-to-water heat pump system that extracts heat from the outside air and transfers it to water, which then circulates through underfloor pipes, radiators or fan coil units. The Mono-Bloc range comes in heating-only and reverse cycle versions; the brochure lists heating water leaving at 15 to 60 °C and cooling water at 5 to 22 °C, with outdoor operation from minus 25 to 35 °C when heating. Cooling has a limit worth knowing. The brochure says fan coil units provide both heating and cooling if required, while it presents radiators only as a heating solution, so a reverse cycle system cools through fan coils or a floor circuit designed for it, not through standard radiator panels. A reverse cycle air conditioner heats the room air directly, which is a different product from a hydronic heat pump. The heat pump also needs no gas connection, which Daikin lists among its features.

Converting an Existing Gas Boiler System to a Heat Pump

An existing gas hydronic system can keep its panels and pipes and change only the heat source. Daikin says Altherma is suitable for retrofits, integrating with existing heat emitters such as underfloor pipes, radiators or fan coils. The question is whether those emitters give enough heat at a heat pump's water temperature. Bosch's boiler can send water at up to 82 °C, while Daikin's Altherma lists heating water up to 60 °C, and panels chosen for a hotter boiler give off less heat at a lower temperature. Each room's panel is therefore checked against that room's heat loss, and the quote names any panel that would need replacing with a larger one or supplementing. Old system water is the second check, since The Quote Yard advises a flush before a new boiler is fitted and the same sludge would reach a new heat pump. Disconnecting the old boiler from the gas supply is gasfitting work for a licensed gasfitter. The Victorian Energy Upgrades heating and cooling discounts page, read on 19 November 2026, lists discounts for reverse cycle air conditioners and does not list hydronic heat pumps, so no discount is assumed in the quote.

Peak Air Conditioning Richmond

Hydronic Heating Service and Repairs in Richmond

The Quote Yard's guide suggests a simple first check that anyone can do: run the heating until it is fully up to temperature, then feel the top and bottom of every radiator and note which rooms are affected. That pattern points to the fault. The sections below cover the service a gas boiler needs and the faults that bring most callouts. Gas ducted heaters are a different appliance, covered on the ducted heating service and repairs page.

Boiler Servicing to AS 4575, Annually or Every Second Year

The Building and Plumbing Commission states that gas servicing work in Victoria must be carried out in accordance with AS 4575, and only plumbers registered or licensed in the specialised class of Type A appliance servicing may do it. Energy Safe Victoria lists domestic central heaters among Type A gas appliances, and The Quote Yard's Victorian guide treats gas-fired hydronic boilers as Type A. Servicing covers internal cleaning, maintenance and adjustment, as well as repairing or replacing a component, and the gasfitter completes the Appendix E checklist, which includes carbon monoxide testing. The customer receives the complete servicing record within 5 days, and it lists the make, model, model number, gas type and serial number. Bosch's manual says an annual service is recommended, that servicing needs a calibrated CO/CO2 analyser and manometer, and that inhibitor concentration should be checked every 12 months. The Quote Yard recommends a service annually or every second year, and Energy Safe Victoria recommends all gas heaters are serviced at least every two years.

Cold Radiators: Bleeding Air and Balancing Flow

The Quote Yard's guide reads a cold radiator by where it is cold. Cold at the top with a warm bottom means air, because air rises to the highest point in any water-filled system and displaces the water there, and the fix is bleeding the air out through the valve at the top corner. Cold all over on one radiator points to a valve: a thermostatic valve seized shut, a lockshield closed off, or a zone not calling for heat. When the radiators nearest the boiler run hot and the far ones stay cool, the system needs balancing, which means resetting the lockshield valves so flow is shared. Bosch's commissioning steps show why bleeding and pressure go together: after air is vented from every radiator, the system is topped back up to between 150 and 200 kPa. The guide also notes that if air keeps returning within weeks, the system is drawing it in somewhere, and that needs finding rather than bleeding again.

Leaks, Pressure Drops and Failed Circulating Pumps

A sealed hydronic system holds a set pressure, shown on the gauge at the boiler. According to The Quote Yard's guide, pressure falling over weeks or months means water is leaving, through a radiator valve, a pipe joint or a weeping relief valve. Pressure swinging sharply between cold and hot points at the expansion vessel, the air cushion that lets heated water expand; Bosch pre-charges the vessel in its boiler to 75 kPa. A relief valve that keeps discharging is usually reporting a flat vessel rather than failing itself. Topping up again and again adds fresh oxygenated water, which speeds up corrosion. The circulating pump is the other common failure: the guide describes a seized pump as a boiler that fires and gets hot while nothing further away heats at all, often after a summer of standing idle, and notes that an air lock in the pump head can mimic failure. Bosch's fault table lists water pressure, trapped air, the pump and leaks as the first checks when its heat exchanger overheats.

Power Flushing Sludge from Older Systems

Hydronic systems are sealed loops of water passing over steel and iron, and The Quote Yard's guide explains that corrosion produces magnetite, a fine black iron oxide sludge that settles wherever the flow slows. It collects first at the bottom of radiators, which is why a radiator that is warm at the top and cold at the bottom points to sludge, not air, and bleeding achieves nothing. Corrosion inhibitor dosed into the water slows the process, but it depletes over time without any warning sign. A power flush circulates high flow water and cleaning chemicals through the system to lift the deposits out. Bosch's manual explains why this matters to the boiler: debris from the system can damage the boiler and reduce efficiency, and it may be necessary to use a power flushing machine. After flushing, the manual has the system refilled with fresh water and a suitable inhibitor, and it does not permit sealing agents in the system water.

Rental Gas Safety Checks Every Two Years

Consumer Affairs Victoria requires rental providers to have a gas safety check done every 2 years by a licensed or registered gasfitter, and the gasfitter must be endorsed in the specialised class of Type A Gas Appliances Servicing. A gas hydronic boiler in a rental home is part of that check. The Building and Plumbing Commission sets out what the check involves: checking the gas installation, testing all gas appliances for leakage and servicing all gas appliances, with the results recorded on a Record of Gas Safety Check. Rental providers must give the renter a copy within 7 days on request. Richmond's rented share is almost double the state's, at 54.7% of dwellings against 28.5% across Victoria (ABS 2021 Census), which makes this rule relevant to many boilers in the suburb. A heat pump hydronic system has no gas to check, but its wiring still falls under the separate 2-yearly electrical safety check.

Abbotsford Emergency Air Conditioning Repair

TESTIMONIALS

What Our Hydronic Heating Customers Say About Us

The Process

3 Step Process For Your Hydronic Heating Needs

Call or Book Between 6am and 10pm

Call the one number any day between 6am and 10pm. The booking notes the system type, the fault or the job, the address, who needs to be present (owner, tenant, agent or building manager) and any building access rules. Same-day visits are arranged where possible.

Inspection and Written Quote

A technician inspects the site and the existing system or the planned unit positions, then gives a written quote listing equipment, labour, extras and old unit removal. For repairs, the diagnosis comes first and any part is quoted before it is ordered. Work starts once the quote is accepted.

Installation or Repair, Testing and Handover

Each trade works under the licence it needs: ARC for refrigerant, a BPC-registered gasfitter for gas and a licensed electrician for wiring. The system is then tested, the controls are explained, and paperwork such as a Certificate of Electrical Safety or a gas compliance certificate is handed over where the job requires one.

FREQUENTLY ASKED QUESTIONS

Hydronic Heating In

Everything you need to know about our Hydronic Heating In

How much does hydronic heating cost to install?

No independent cost guide read for this page gives a current installation price for a new hydronic system, so no figure is quoted. Energy.gov.au describes the purchase and installation costs as high, and YourHome says hydronic heating is typically more expensive to buy and install than space heaters. The price is set by the number and size of panels, whether the pipes go in a slab, under a timber floor or to wall panels, the choice of gas boiler or heat pump, and the length of the pipe runs. A written quote is given after the home has been inspected.

What is hydronic heating?

Hydronic heating warms a home with water rather than air. YourHome describes it as circulating hot or cold water or other fluid through radiator panels in rooms or under the floor, with the fluid heated by electric heat pumps, solar collectors, or gas if the system is used for heating only. A circulating pump moves the water from the heat source to each panel or floor circuit and back. Energy.gov.au notes that its operation is silent and that it does not distribute dust particles.

Is hydronic heating expensive to run?

It depends mostly on the heat source. Energy.gov.au says hydronic running costs are lower when the system is powered by solar or electric heat pumps, and Daikin states that its Altherma heat pump releases more than 4 kW of heat for each 1 kW of electricity. A gas boiler burns gas and also uses some electricity for its pump. No independent source read for this page gives a dollar running cost, so the bill depends on the energy tariff, the insulation and the hours the system runs.

What are the downsides of hydronic heating?

The upfront cost is high, as both energy.gov.au and YourHome note. It is slower to warm a cold house: The Quote Yard's guide says a hydronic system takes longer than ducted air, so a timer that starts it early works best. Radiator panels take wall space, which Daikin's underfloor guidance points out when it calls the floor version hidden. A gas boiler system heats only, and the water needs occasional bleeding and fresh corrosion inhibitor to keep the radiators working evenly.

Can a gas hydronic system be converted to a heat pump?

Yes. The existing panels and pipes can stay where they suit the new heat source, and only the heat source changes; Daikin says Altherma suits retrofits with existing radiators, underfloor pipes and fan coils. Each panel is checked against its room's heat loss, because a heat pump such as Altherma supplies water up to 60 °C, cooler than a boiler such as Bosch's at up to 82 °C. Old system water may need a flush first, and a licensed gasfitter disconnects the gas boiler. The Victorian Energy Upgrades discounts page does not list hydronic heat pumps, so no discount should be assumed.

How often should a hydronic heating boiler be serviced?

The Quote Yard recommends a boiler service annually or every second year, Bosch's boiler manual recommends an annual service, and Energy Safe Victoria recommends all gas heaters are serviced at least every two years. In Victoria the service must follow AS 4575, including the Appendix E checklist with carbon monoxide testing, and the customer receives the record within 5 days. Rental providers must also have a gas safety check done every 2 years, which Peak Air Conditioning Richmond can arrange through a licensed gasfitter during a booked visit.

Request A Free Hydronic Heating Quote

GET A FREE QUOTE