This page covers the air conditioning installation Richmond homes actually need: wall-mounted splits for single rooms, multi-head systems that run several rooms from one outdoor unit, and ducted or slim bulkhead systems hidden in the ceiling. Richmond's housing makes the choice specific. The 2021 Census counted 53.0% of the suburb's homes as flats or apartments and 30.7% as semi-detached, row or terrace houses, so owners corporation approval, narrow side passages and long pipe runs come up often. Peak Air Conditioning Richmond works out the size room by room in kilowatts, plans the outdoor unit position around EPA Victoria's noise rules and gives a written quote after an inspection. Refrigerant work is carried out under an ARC refrigerant handling licence, and new electrical work comes with a Certificate of Electrical Safety. Call 0468 046 042 for a free written quote.
GET A FREE QUOTE
Peak Air Conditioning Richmond installs, repairs, services and cleans heating and cooling systems across Richmond and 12 nearby suburbs. Two things set out what a buyer gets before any work is booked: a written quote that itemises the job, and one phone line that covers all 12 services from 6am to 10pm. Each trade's work is done under the licence it requires: an ARC refrigerant handling licence for refrigerant work, a licensed gasfitter registered with the Building and Plumbing Commission for gas work, and a licensed electrician, who issues a Certificate of Electrical Safety, for wiring.
The right system depends on how many rooms need heating and cooling, where an indoor unit can sit and how much ceiling space the building has. Most split systems sold in Melbourne do both jobs: Mitsubishi Electric's own FAQ notes that most split system air conditioners perform both heating and cooling. The four types below are what a Richmond home usually chooses between.
A wall-mounted split pairs one indoor head, mounted high on an inside wall, with one outdoor unit joined to it by refrigerant pipes. It is the usual answer for a single bedroom, a living room or a home office. Mitsubishi Electric's MSZ-AP series, for example, covers 2.5 kW to 7.8 kW, uses R32 refrigerant and runs as quietly as 18 dB(A) in heating mode, which matters in a bedroom. Daikin's wall range includes the Alira X, Zena and Cora models. The split system installation page covers the single-room job step by step.
A multi-head system connects several indoor units to a single outdoor unit, which saves wall and courtyard space on a tight block. Mitsubishi Electric's MXZ range runs from 2 ports on the 5.2 kW MXZ-2F52 to 6 ports on the 12.0 kW MXZ-6F120. The trade-off is that the outdoor unit's output is shared. In the brand's own example, an MSZ-AP50 head on an MXZ-4F71 gives up to 4.0 kW while a second head is also cooling, against its full 5.0 kW when it runs alone. Each room still sets its own temperature within the same operating mode, and unused heads can be switched off.
A ducted system places one indoor unit in the roof space and sends air through ducts to outlets in each room, so Daikin notes that only the controller, the return air grille and the discharge grilles are visible inside the home. A slim bulkhead unit is the compact, single-room version, boxed into a bulkhead or a shallow ceiling. Mitsubishi Electric's PEAD series stands just 250 mm high across its 5.0 kW to 14.0 kW range, made for low ceilings and tight bulkhead cavities. The brand also draws the line clearly: a bulkhead system serves one room, while a ducted system serves several. Whole-home systems are covered on the ducted air conditioning page.
A floor-standing unit sits low on the wall, near skirting height, and suits rooms where a high wall mount will not fit, such as a room under a sloping ceiling or a wall broken up by tall windows. Daikin sells its split range as either wall mounted or floor standing, and describes floor-standing models as suited to rooms where upper wall installation is not possible and to homes where heating is the priority for more months of the year. Mounted low, the unit warms the lower part of the room more effectively. A high wall head, by contrast, is mounted up high for better airflow when cooling.


A system that is the wrong size or in the wrong place costs more to run and does the job badly, so the planning happens before any hole is drilled. The four stages below follow the order an installation runs in, from the heat load calculation through to the paperwork at handover.
Capacity is measured in kilowatts. The government Energy Rating label's capacity panel shows how many kilowatts of heating and cooling a unit delivers at set outdoor temperatures, and the higher the figure, the more heating or cooling the system provides. Floor area alone is not enough to pick a size. A proper heat load looks at floor area, ceiling height, insulation, glazing and orientation, the same factors Rinnai lists for sizing its Brivis ducted heaters. A west-facing bedroom with a large window and no ceiling insulation needs more capacity than a shaded room of the same size. The Energy Rating advice is to choose the size first, then use the star rating to compare similar models.
The outdoor unit needs clear airflow around it, a solid pad or wall bracket and a position the pipes can reach. In a dense suburb it also has to respect the neighbours. EPA Victoria's residential noise rules treat an air conditioner used for heating as unreasonable on weekdays before 7am and after 10pm, and on weekends and public holidays before 9am and after 10pm, if someone in a habitable room of another home can hear it. For cooling, the evening cut-off moves to 11pm. Placing the unit away from a neighbour's bedroom window keeps early-morning and late-night use inside the rules.
Insulated refrigerant pipes, a power and control cable and a condensate drain run between the indoor and outdoor units, usually through one drilled hole in the wall behind the indoor head. A short, direct run is simpler and cheaper, and the hole is sealed afterwards to keep weather and pests out. The drain carries away the water the indoor coil pulls from the air while cooling, so it has to fall for the water to run off. Mitsubishi Heavy Industries notes that water leaking from an indoor unit can mean it was installed so the water cannot run off, while water running from the drain pipe beside the outdoor unit is a sign the system is working and was installed correctly.
Before any refrigerant is released into new pipework, the joints are pressure tested with oxygen-free nitrogen and the lines are then evacuated. The Australian Refrigeration Council's Cool Change bulletin states that a pressure test and inspection before evacuation is required for all refrigeration and air conditioning piping, and that site-built sections must be tightness-tested before the system is charged with refrigerant. Clean, leak-free lines are what let moisture be removed properly during evacuation. Commissioning then follows the manufacturer's instructions, running the system to check it heats and cools as it should. Where new electrical work is done, a Certificate of Electrical Safety is required under the Electricity Safety Act 1998, and the electrician must give the customer a copy, within 30 days for non-prescribed work.
Choosing an installer comes down to three practical questions: who is legally allowed to do the work, what the price actually covers and whether a booking can fit around the household. Each one is answered plainly below.
Australian law requires anyone who handles refrigerant or works on refrigeration and air conditioning equipment to hold a refrigerant handling licence. The Australian Refrigeration Council (ARCtick) defines handling to include installing and commissioning that equipment, whether or not refrigerant is present. On a Peak Air Conditioning Richmond installation, the refrigerant work is done under that licence, and the electrical connection is done by a licensed electrician who issues the Certificate of Electrical Safety. It is reasonable to ask to see the technician's licence before work starts. The manufacturer warranty applies when the system is installed to the manufacturer's requirements, which is one more reason the licensed steps matter.
A price given over the phone cannot see a long pipe route, a crowded switchboard or a building that needs owners corporation approval, so the quote follows an inspection. The written quote names the unit model and its kilowatt capacity, marks where the indoor and outdoor units will go and describes the pipe route between them. It also notes any approval the home needs before work can start and the expected timing of the job. With those details on paper, a homeowner can compare two quotes on the same terms instead of comparing a headline price. The inspection and the written quote are free, with no obligation to go ahead.
Inspections and installs can be booked from 6am to 10pm, seven days a week, so a visit can fit around work rather than costing a day off. That matters in Richmond, where the 2021 Census counted 54.7% of homes as rented, so a landlord, a property manager and a tenant often all need a time that suits. Early and evening times also help in apartment buildings where a building manager sets trade access windows. A Melbourne air conditioning guide notes that the first serious heatwave in December fills the diary, so an inspection in spring gives the widest choice of install dates. Same-day inspections are offered where possible.


The figures below come from independent Melbourne cost guides and installer benchmarks published in 2026. They are indicative ranges, not Peak Air Conditioning Richmond's own prices, and the actual price is set in a written quote after an inspection. Back-to-back means the indoor and outdoor units sit on opposite sides of the same wall, the simplest install.
The Melbourne table on whatsthedamage, updated November 2026, puts supply and installation of a back-to-back split at around $1,250 to $2,625 for 2.5 kW, $1,475 to $2,950 for 3.5 kW, $1,900 to $3,675 for 5 kW, $2,300 to $4,725 for 7 kW and $3,150 to $5,800 for 9 kW. Climate Control Solutions, a Melbourne installer, puts a 3.5 kW back-to-back job at around $2,100 to $2,600 in its July 2026 figures. The spread inside each size comes from the brand, the star rating and how straightforward the install is.
For multi-head systems, the same Melbourne table lists 2 heads at $4,200 to $7,900 and 4 heads at $7,350 to $12,600, supplied and installed. Climate Control Solutions compares two separate 3.5 kW splits at about $4,600 to $5,800 with a 2-head multi-head at around $4,000 to $5,200. Standard ducted reverse cycle for a 3-bedroom home runs $8,400 to $14,700 in the whatsthedamage table, and premium or zoned room-by-room systems $12,600 to $23,100. QuickAir's 2026 Melbourne guide puts ducted for a small 1 to 2-bedroom home at $5,000 to $8,000.
Paying only for the installation of a unit bought elsewhere costs $735 to $1,575 in Melbourne, with $1,000 typical, according to whatsthedamage. Hipages puts installer labour at $80 to $110 an hour nationally. Extras sit on top of either price. Climate Control Solutions advises allowing roughly $450 for the licensed electrical work when a new circuit is needed. A longer pipe run, an outdoor unit on a second-storey wall or a roof, and hard-to-reach wall or roof access all add labour and materials, and these are the items most likely to separate two quotes for the same unit.
With the system types set out above, the real decision is about trade-offs: running cost, control and the size of the home. In Richmond the answer usually turns on how many rooms are used at once and whether the roof space can take ductwork at all.
For a home that heats or cools one or two rooms at a time, room splits usually cost less to run because they condition only the rooms in use. The Australian Government's YourHome guide notes that ducted systems are less energy efficient because they need energy for fans to push air through the ducts, and that heating or cooling can be lost through ducts that are not well insulated and sealed. Zoning narrows the gap by shutting off unused areas. Against gas heating, either type can save money: the Victorian Energy Upgrades program lists bill savings of up to $460 a year for replacing a non-ducted gas space heater, and up to $1,140 a year for a ducted gas heater.
Each split head has its own remote and runs only when its room needs it, so a bedroom can sit at a different temperature from the living room without affecting it. Ducted systems control by zone instead. Mitsubishi Electric's zone controller can create up to 4 or 8 separate zones, and the brand suggests cooling the living areas during the day and switching to the bedrooms at night. It also notes that the right zoning layout depends on the floor plan, the household's routine and the system's capacity. One wall controller then runs the whole house, and no indoor head is visible on any wall.
Most Richmond homes are small. The 2021 Census counted 22.4% of the suburb's dwellings with one bedroom and 43.8% with two, against 5.1% and 19.1% across Victoria. In a one-bedroom apartment, a single wall split in the living area, sometimes with a second head in the bedroom, usually covers the home without the roof space that ducting needs. In a two-bedroom terrace, a 2 or 3-head multi-head system keeps a single outdoor unit on a small courtyard. Ducted becomes worth pricing when there is accessible roof space and several rooms are in use at once, which is more common in the 26.0% of Richmond homes with three bedrooms.


Richmond's building stock is unusually mixed. Wikipedia describes the inner-city suburb, 3 km east of the CBD in the City of Yarra, as a blend of converted warehouse residences, public housing high-rise flats and Victorian-era terrace houses, and each one changes how a system goes in.
Most Richmond houses are single-fronted Victorian homes built from the 1850s to the 1930s, typically on long, thin blocks with two bedrooms at the front and the family room and kitchen at the back. That layout decides the pipe route. A bedroom head at the front is a long way from the rear courtyard, which is often the most practical spot for the outdoor unit, so the pipes run either through the roof space or along a narrow side passage, and the extra length adds cost. Where the front bedrooms and the back living area both need conditioning, a multi-head system with one outdoor unit at the rear can feed each room on its own pipe run.
Flats and apartments make up 53.0% of Richmond's occupied dwellings (ABS 2021). Under Victoria's model rules for owners corporations, which apply where the owners corporation has not made its own rule on the point, an owner or occupier must get the owners corporation's written approval before changing the external appearance of their lot, and must not damage or alter common property without written approval. An outdoor unit on a balcony, or pipes through an external wall, is likely to need that approval. The model rules also say approval cannot be unreasonably withheld, although reasonable conditions can be attached, such as where the outdoor unit may sit.
Richmond's converted warehouse residences, and landmark conversions such as The Malthouse, where silos were turned into apartments, can have taller rooms and more open living space than a standard house. Where a conversion does have a high ceiling, the heat load rises with the room volume, and warm air gathers up high while the living area below stays cool in winter. The YourHome guide notes that in larger rooms with high ceilings a combination of radiant and convective heating works best. A large-capacity head, such as Daikin's XL Series made for large open-plan living, or a floor-standing unit that heats from low down, often suits these spaces better than a standard wall split.
With 54.7% of Richmond homes rented, rental rules shape many installs. Consumer Affairs Victoria requires all rental properties to have a fixed heater in good working order in the main living area, and for agreements entered into from 29 March 2023 it must be an energy efficient fixed heater. Landlords with older agreements should check the current Consumer Affairs Victoria rules. The Victorian Energy Upgrades program also states that when a space heater in a rental home breaks and cannot be repaired after 1 March 2027, it must be replaced with an efficient reverse cycle air conditioner with an outlet in the main living area. Separately, rental gas and electrical safety checks are due every 2 years.
Replacing a system raises questions a new install does not: whether the old unit can keep going, what happens to it once it comes off the wall and whether a gas heater can be retired at the same time.
Many older air conditioners run on R22. The Australian Refrigeration Council notes that Australia largely phased out imports of HCFCs, including R22, in 2016, with a small allowance of 2.5 ozone depletion potential tonnes a year permitted to service equipment until 2029. After 2029, the maintenance of remaining R22 systems will rely on recycled or reclaimed refrigerant, so a leak repair may become harder to arrange. The ARC also says an R22 system in good working order does not need to be replaced and can still be serviced with R22. Current splits such as Mitsubishi Electric's MSZ-AP series use R32 instead.
A like-for-like changeover takes out the old unit and fits a new one, often in the same position so the existing wall penetration can be reused. Whatsthedamage puts a Melbourne changeover with the old unit removed at $1,575 to $3,150, with $2,200 typical, and removal and disposal of an old unit on its own at $105 to $370. Climate Control Solutions says removal adds about $250 per unit. Taking an old split out is refrigerant work too: the ARC's restricted split system licence covers decommissioning as well as installation, so the old unit's refrigerant is handled by a licensed technician before it leaves the house.
Swapping a gas heater for an efficient reverse cycle system can attract a discount under the Victorian Energy Upgrades program. The program lists discounts of $630 to $1,610 for replacing a non-ducted gas space heater with a 3 kW to 9 kW system, and up to $5,530 when a ducted gas heater is removed or replaced, or up to $2,520 when it is replaced with 4 split systems. The product must be approved under the program, and the home must be more than 2 years old. Disconnecting the gas heater is gas work for a licensed gasfitter registered with the Building and Plumbing Commission. The reverse cycle air conditioning page explains how these systems heat a home.


Call the one number any day between 6am and 10pm. The booking notes the system type, the fault or the job, the address, who needs to be present (owner, tenant, agent or building manager) and any building access rules. Same-day visits are arranged where possible.

A technician inspects the site and the existing system or the planned unit positions, then gives a written quote listing equipment, labour, extras and old unit removal. For repairs, the diagnosis comes first and any part is quoted before it is ordered. Work starts once the quote is accepted.

Each trade works under the licence it needs: ARC for refrigerant, a BPC-registered gasfitter for gas and a licensed electrician for wiring. The system is then tested, the controls are explained, and paperwork such as a Certificate of Electrical Safety or a gas compliance certificate is handed over where the job requires one.
Melbourne cost guides put a supplied and installed 3.5 kW back-to-back split at around $1,475 to $2,950, a 2-head multi-head system at $4,200 to $7,900 and standard ducted reverse cycle for a 3-bedroom home at $8,400 to $14,700 (whatsthedamage, November 2026). Install-only work on a customer-supplied unit runs $735 to $1,575. A long pipe run, a new circuit and difficult access all add to these figures. A free written quote is given after an inspection of the home.
An installation starts with an inspection and a heat load assessment that sets the kilowatt size and the indoor and outdoor positions. On the day, the indoor and outdoor units are mounted, the wall is drilled for the pipes, cable and drain, and the refrigerant lines are connected. The pipework is pressure tested with oxygen-free nitrogen and evacuated before the refrigerant is released, then the system is commissioned and checked in heating and cooling. Any electrical work is covered by a Certificate of Electrical Safety, and the controls are explained at handover.
For a home that heats or cools one or two rooms at a time, split systems usually cost less to run because they condition only the rooms in use. Ducted systems use extra energy for the fan that pushes air through the ducts, and the YourHome guide warns of energy lost through ducts that are not well insulated and sealed. Zoning reduces that gap by switching off unused areas. Compared with gas heating, either type can save money, with the Victorian Energy Upgrades program listing savings of up to $1,140 a year for replacing a ducted gas heater.
Usually, yes. Victoria's model rules for owners corporations, which apply where the owners corporation has not made its own rule, require written approval before an owner or occupier changes the external appearance of their lot or alters common property. An outdoor unit on a balcony or pipes through an external wall is likely to fall under those rules. Approval cannot be unreasonably withheld, but reasonable conditions can be attached, so it is best to apply before the installation is booked.
Yes. The Australian Refrigeration Council states that anyone who handles refrigerant or works on refrigeration and air conditioning equipment must hold a refrigerant handling licence, and that includes installing and commissioning a split system. The electrical connection must be done by a licensed electrician, who issues a Certificate of Electrical Safety. If a gas heater is disconnected as part of the job, that gas work needs a licensed gasfitter registered with the Building and Plumbing Commission. Peak Air Conditioning Richmond has the refrigerant, electrical and any gas work done under the licence each one requires.
A single back-to-back wall split is often installed within a day. Multi-head systems, long pipe runs through a terrace roof space and ducted systems take longer. In an apartment, the start date can also depend on when the owners corporation approval comes through. The written quote sets out the expected timing for the specific job, so the household knows how long the work will take before it is booked.

GET A FREE QUOTE
BUSINESS
SERVICES
OPERATING HOURS
Sun: 6:00am - 10:00pm
Mon: 6:00am - 10:00pm
Tue: 6:00am - 10:00pm
Wed: 6:00am - 10:00pm
Thu: 6:00am - 10:00pm
Fri: 6:00am - 10:00pm
Sat: 6:00am - 10:00pm