Air conditioning Clifton Hill work here covers split systems, multi-head systems, ducted air conditioning, reverse cycle heat pumps, zoned ducted heating, servicing, repairs and regas. Clifton Hill is a City of Yarra suburb 4 km north-east of the Melbourne CBD, and most of its homes are attached: the ABS 2021 Census counts 50.8% of occupied dwellings as semi-detached, row or terrace houses or townhouses, against 13.9% across Victoria, with 24.9% flats or apartments and 23.8% separate houses. Wikipedia describes single and double storey Victorian and Edwardian dwellings and says the suburb is almost completely included in heritage planning controls. So the outdoor unit's position, the wall the pipes pass through and the council's heritage conditions are worked out on site before any model is picked. Each job starts with an inspection and a written quote, and bookings are taken 6am to 10pm, seven days.
GET A FREE QUOTE
Peak Air Conditioning Richmond installs, repairs, services and cleans heating and cooling systems across Richmond and 12 nearby suburbs. Two things set out what a buyer gets before any work is booked: a written quote that itemises the job, and one phone line that covers all 12 services from 6am to 10pm. Each trade's work is done under the licence it requires: an ARC refrigerant handling licence for refrigerant work, a licensed gasfitter registered with the Building and Plumbing Commission for gas work, and a licensed electrician, who issues a Certificate of Electrical Safety, for wiring.

The form of a Clifton Hill house shapes its air conditioning layout more than its floor area does. Wikipedia describes a mix of single and double storey homes, some freestanding and many in semi-attached rows, and the ABS 2021 Census puts the average at 2.6 bedrooms per dwelling against 3.1 for Victoria. The three layouts below follow those house forms, from wall splits in a single-storey cottage to a ducted system in a freestanding house, and the inspection confirms which one a given house can take.
One layout for a single-storey cottage starts with a wall split in the living room and adds a second in the main bedroom, rather than putting a unit in every room. Two-bedroom dwellings make up 39.1% of Clifton Hill homes in the ABS 2021 Census, about double the Victorian share of 19.1%, so a living room and main bedroom layout matches a large share of homes here. The wall decides where each indoor unit goes, not the brand. Mitsubishi Electric's MSZ-AP installation manual asks for a rigid wall without vibration, a fixing height of 1.8 m to 2.3 m from the floor, a spot where warm or cool air spreads across the whole room, and a position where the air filter can be lifted out easily. In a cottage whose front room faces the street, the indoor unit can still sit in that room while its pipes travel through the roof space or under the floor to an outdoor unit at the back. The same manual allows up to 20 m of pipe on these models, with the first 10 m pre-charged on the smaller sizes, so the length of that route is measured at the inspection before the quote is written.
Where a double-storey terrace has its bedrooms upstairs and limited outside space at the back, a multi-head system is built for that limit. Mitsubishi Electric describes multi-head systems as several indoor units connected to a single outdoor unit, and says the design takes up less space outside and lessens the outdoor units' effect on the look of the house. Its MXZ range runs from 2 ports on the MXZ-2F52 to 4 ports on the MXZ-4F71 and MXZ-4F80, 5 on the MXZ-5F100 and 6 on the MXZ-6F120. Two points come with the shared outdoor unit. Capacity is divided between the heads that are running at the same moment, and every head runs in the same mode, so an upstairs bedroom cannot cool while the living room heats. Heads that are not in use can be switched off. The Quote Yard's servicing guide notes that multi-head installations are common through the inner suburbs where outdoor space is limited, and that each head keeps its own filters, coil and condensate drain, so an upstairs head needs a drain route planned down through the house or the wall.
Separate houses are 23.8% of Clifton Hill's occupied dwellings in the ABS 2021 Census, against 73.4% across Victoria, and a freestanding house is the form on this page where ducted is assessed, where the roof space allows. Mitsubishi Electric says ducted air conditioning can be installed in an existing home, that the process needs access to the ceiling cavity, and that a qualified installer assesses the roof space to plan the duct routes. Its PEA-M-HAA units have a two-piece construction that lets them go in through ceiling access, and its PEAD bulkhead series stands 250 mm high for low ceilings and tight cavities. The Quote Yard's servicing guide adds a caution: older housing through the inner and middle suburbs was never designed around ducted systems, which is why retrofitted splits and multi-heads are so widespread there. Daikin says retrofitting ducted into an existing home can be more complex. So a freestanding Victorian or Edwardian house is checked for ceiling depth, a path for the ducts and a place for the return air grille before ducted is quoted. The full method is on the ducted air conditioning page.
Wikipedia calls Clifton Hill a relatively intact example of late 19th and early 20th century development. Clement Hodgkinson laid it out as a government subdivision in the 1860s, with wider streets than most of inner Melbourne, and by the end of the 1880s boom it was described as street after street, row after row, of neat brick buildings. Three features of that housing shape an install: the heritage controls on the street frontage, the shared walls of semi-attached rows, and the brick the pipes have to pass through.
Wikipedia says Clifton Hill is now almost completely included in heritage planning controls, and the City of Yarra's Database of Heritage Significant Areas (March 2024) bears that out: most of its addresses sit in two area overlays, HO316 and HO317, and each property is graded individually significant, contributory or not contributory. Yarra City Council says a planning permit is normally required for works in a heritage overlay, and that even installing services can need one. Its heritage permit-exemption plan, in the July 2014 version linked from the council site, exempts an air conditioner on a residential building that is visible from a street (other than a lane) or a public park where it is fixed to the rear wall or sits in the rear setback. On a side wall or in a side setback it must sit at least 4 metres behind the front facade on individually significant and contributory properties, or 2 metres on not contributory ones. The exemption does not cover corner properties, and the plan does not apply to places on the Victorian Heritage Register, where Heritage Victoria decides. The plan adds that a building permit may still be needed. Because the plan may have been updated, the owner checks the grading and the current rules with Yarra City Council (03 9205 5555) before an outdoor unit goes on. A rear-wall position fits the exemption most simply, which is how a unit stays off the street frontage.
Semi-detached, row and terrace houses make up 50.8% of Clifton Hill's occupied dwellings (ABS 2021), nearly four times the Victorian share of 13.9%, and in a semi-attached row the house next door is part of the outdoor unit decision. The options are the rear wall on brackets, a stand or pad in the back yard, or a lower roof at the back where the structure can take it; which one works is settled at the inspection, not by rule. Mitsubishi Electric's MSZ-AP manual sets the tests for the spot: a rigid wall or support so operating sound and vibration do not grow, a place where neighbours are not bothered by the sound or by hot or cool air, clearances of 100 mm on the tightest sides to 350 mm on the widest with open space above, and a pipe loop near the unit to cut vibration. It also says the outdoor unit makes condensate when heating, so it is placed where that water will not wet the ground beneath or a neighbour's path. As a general installer approach, brackets are kept off a wall shared with the house next door, because vibration carries through it. Timing counts as well: EPA Victoria says a unit used for heating must not be heard in another home's habitable room before 7am or after 10pm on weekdays.
Many of Clifton Hill's 1880s cottages are brick, going by Wikipedia's account of the boom years, and the wall type is confirmed on site. In a brick wall the pipe hole is usually cut with a core drill, a hollow bit that cuts a clean round hole instead of breaking bricks out with a hammer drill; that is general installer practice rather than a manufacturer rule. The manufacturer sets the hole itself. Mitsubishi Electric's MSZ-AP manual specifies a 65 mm hole, with the outdoor side 5 to 7 mm lower than the indoor side so condensate drains outwards, a sleeve fitted through the wall and the gap sealed with putty. Outside, it calls for every pipe joint to be covered, all outdoor piping and valves to be insulated with 8 mm insulation, and bends no tighter than a 100 mm radius, which keeps the run along the wall neat. Sealing matters in an old house. Yarra City Council's heritage energy guide says draughts and air leakage are a significant problem in heritage buildings and that blocking draughts is often the most cost-effective way to improve comfort, so a penetration left unsealed would add one more gap. Placing the hole in the rear wall keeps it away from the face brick of the street facade and fits the heritage conditions above.


Most Clifton Hill homes are owner-occupied: 59.5% in the ABS 2021 Census, 29.2% owned outright and 30.3% with a mortgage, while 39.2% are rented. What an owner, or a landlord with a tenant in place, gets from Peak Air Conditioning Richmond is set out below in the order the job runs: the quote, the licensed work and the booking hours.
The quote follows an inspection because the parts of a Clifton Hill job that set the price are hidden until someone looks. For a ducted system, that means getting into the roof space: Mitsubishi Electric's ducted installation manual asks for service access to the motor, fan, drain pump, coil and electrics, and shows access doors of 450 by 450 mm and 600 by 600 mm, so a ceiling with no hatch of that size changes the plan. For split and multi-head systems, it means standing at each wall where a unit could go and finding the outdoor spot that meets the heritage grading and the clearances. The written quote then names the system model and its kW rating, the room each indoor unit serves, where the outdoor unit goes, the pipe route and its length, and whether a new electrical circuit is needed. It lists any step the job depends on, such as a heritage check with Yarra City Council or owners corporation approval in a block of flats, along with the expected timing. That lets an owner compare quotes line by line.
An air conditioning job crosses three trades, and each part is done by the holder of the licence that part needs. The Australian Refrigeration Council states that any person who handles refrigerant or works on refrigeration and air conditioning equipment must hold a refrigerant handling licence, which covers installing, commissioning and servicing. Mitsubishi Electric's installation manual says that, under AS/NZS 3000, the wiring between the indoor and outdoor units must be installed by a licensed electrical contractor. For that electrical work, Energy Safe Victoria requires a Certificate of Electrical Safety, with a copy given to the customer within 30 days for non-prescribed work and within 4 days for prescribed work. Gas heater disconnections and gas ducted servicing go to a licensed gasfitter registered with the Building and Plumbing Commission. For a rental gas safety check, Consumer Affairs Victoria says the gasfitter must be endorsed for Type A appliance servicing on the Plumbers Identity Card, and Energy Safe Victoria suggests asking to see the licence card and the registered classes listed on its back.
Bookings are taken from 6am to 10pm on every day of the week, weekends included, and the line is not staffed between 10pm and 6am. Those hours suit an owner who works during the day and wants to arrange an inspection early in the morning or in the evening. In a rented home the timing involves more people. Consumer Affairs Victoria says that for repairs the rental provider gives the renter at least a full day's notice, and that entry is only between 8am and 6pm on any day except a public holiday, though for an urgent repair a renter may agree to other times or shorter notice. So a booking for a rented Clifton Hill home is usually made by the landlord or agent, with the visit time agreed with the tenant.
Wikipedia says Hoddle Street bisects Clifton Hill, dividing it into western and eastern precincts, and names Queens Parade, Heidelberg Road and Alexandra Parade as the other major roads through it. Clifton Hill station sits at the corner of Hoddle and Ramsden Streets, opposite Mayors Park and the Darling Gardens. In the City of Yarra's heritage database the streets named below west of Hoddle Street fall in overlay HO317 and those to the east in HO316, with the Queens Parade shopping strip in HO330, so each precinct brings its own mix of gradings.
Queens Parade is a local shopping strip of mainly Victorian era shopfronts, according to Wikipedia, which says the cable tram that reached Clifton Hill in 1887 spurred the Queens Parade commercial district around its terminus. The corner of Queens Parade and Gold Street was known locally as Little Hollywood. Yarra's heritage database lists many of these buildings as shop and residence, graded contributory, with some, such as Campi's Buildings, graded individually significant. That matters for air conditioning, because the council's heritage exemption for air conditioners covers residential buildings only, so a condenser for a shop on the parade is a question for Yarra City Council first. The equipment differs from a house as well. For a heritage shopfront, Mitsubishi Electric points to its under-ceiling units where exposed ceilings or heritage features rule out a ducted system, and describes its SUZ-M outdoor units as particularly suited to shop front installations. Because the database records these buildings as a shop and a residence together, the quote separates the shop's system from any work on the home above or behind it, and the council confirms which rules apply to each. Larger systems are covered under commercial air conditioning.
West of Hoddle Street, OpenStreetMap places the Darling Gardens between Gold Street on the west and Hoddle Street on the east, with Mayors Park just north of them beside the station, and South Terrace running along the gardens' southern edge. The land for the Darling Gardens was reserved in 1862 (Wikipedia), and Yarra's database lists the gardens as individually significant. Wikipedia notes that blocks of flats were built on prominent streets such as South Terrace in the 1960s, overlooking the gardens, and the database grades those blocks not contributory while most of the houses between them are contributory. Two rules follow for an install. The permit-exemption plan's conditions apply to units visible from a public park as well as a street, so a wall facing the Darling Gardens is treated like a street front. In the flats, the owners corporation's rules come first; where it has none of its own, Consumer Affairs Victoria's model rules 5.2 and 4.3 require written approval before the external appearance of a lot or the common property is changed. Hodgkinson Street and Gold Street, also in HO317, are mostly graded contributory, so the 4 metre side-setback condition is the one that usually applies.
East of Hoddle Street, Wikipedia places the old City of Melbourne quarry between Yambla Street and the Merri Creek, with private quarries between Ramsden and Roseneath Streets. The council quarry had become a tip by the 1960s and was later redeveloped into a park at the corner of Ramsden and Yambla Streets, now Quarries Park. OpenStreetMap shows Yambla Street running north-south beside the park's western edge. Yarra's database lists Yambla Street's houses in overlay HO316, most graded contributory and dated 1880 to 1890, and two blocks of 1960s flats graded not contributory. For an install, homes facing the park meet the same public park condition as the western precinct, and corner blocks, such as those where Ramsden Street meets Yambla Street, fall outside the exemption altogether, because the plan does not apply to corner properties. Most of the listed houses on Ramsden and Roseneath Streets are graded contributory in the same overlay, so a rear-wall position is the first option checked across the precinct, and the flats answer to their owners corporation as on South Terrace.


QuickAir, a Melbourne installer, says most Melbourne homes run heating harder than cooling, so on this page heating comes first. Yarra City Council's guide to energy efficiency in heritage buildings adds the starting point: most were built with no thought of insulation and with single glazing, and draughts through cracks and gaps are common, so the council lists blocking draughts first, ceiling insulation second (it suggests at least R4.0 in Yarra) and double glazing third. The three routes below run from a single heat pump to a whole-house switch away from gas. Water-based hydronic heating, with radiator panels or pipes under the floor, is a separate option with its own design questions.
A reverse cycle air conditioner is a heat pump, and in a home where heating does the harder work, its heating figures are the ones to compare. The Australian Government's Zoned Energy Rating Label shows heating capacity at two outdoor temperatures and cooling capacity at only one, and the Energy Rating site explains that the higher the kW value, the more heating the unit delivers at that outdoor temperature. Heating and cooling efficiency can differ on the same unit: Mitsubishi Electric's MSZ-AP25 carries heating star ratings of 3.5, 3 and 3 across the hot, average and cold zones, against cooling ratings of 6, 5.5 and 6. The Energy Rating calculator finds the right zone from a postcode, and its guidance is to choose the size first and then compare star ratings between similar models. Mitsubishi lists an outdoor operating range for heating down to minus 15 °C on the MSZ-AP series. Its buying guide says size is set by a heat load calculation, not by floor area, weighing insulation, windows, the sides that face the sun and ceiling height. As a general approach, the calculation is run on the house as it stands, so any draught sealing or ceiling insulation planned beforehand is worth mentioning at the inspection.
Homes with three or more bedrooms make up 51.3% of Clifton Hill dwellings in the ABS 2021 Census (38.4% with three and 12.9% with four or more), against 74.1% across Victoria. In those homes zoning lets one system heat only the rooms in use. Mitsubishi Electric suggests conditioning the living areas during the day and switching to the bedrooms at night, and its sources give two zone counts: the ducted product page says its Zone Controller creates up to 4 or 8 separate zones, while its May 2026 Zone Controller brochure lists 4-zone and 10-zone models with on/off or linear damper control. On the gas side, Rinnai lists the Brivis Buffalo BX5C as ZonePlus compatible for up to 4 zones. Outlet position matters for heating. YourHome, the Australian Government's guide, says floor outlets are often better than ceiling outlets for heating because warm air rises, and that ceiling outlets can work too where rooms are sealed from draughts. It also says every outlet needs a return air path, such as a gap under the door, back to the central return. Both gas ducted and ducted reverse cycle options are set out under ducted heating.
Replacing gas heating with a heat pump has state support. The Victorian Energy Upgrades page on energy.vic.gov.au (updated 29 October 2026) lists a discount of up to $1,610, and bill savings of up to $460 a year, when a non-ducted gas space heater is replaced with an efficient reverse cycle air conditioner, and up to $5,530 off, with savings of up to $1,140 a year, when a ducted gas heater is removed or replaced. For terraces where ducts are hard to run, its table also covers replacing a ducted gas heater with room systems: up to $2,520 for four split systems (one 8 kW and three 3 kW), or up to $2,940 for a multi-split on one 10 kW outdoor unit. The product must be approved under the program, be high-efficiency and carry a minimum 5-year warranty for a home, and a replaced system must be in a property more than 2 years old. The old gas heater is disconnected by a licensed gasfitter registered with the Building and Plumbing Commission, which requires a compliance certificate within five days for work that modifies consumer gas piping. energy.vic notes that a dual-fuel home pays 2 service charges and an all-electric home 1, and puts the saving at around $1,900 a year for a home without solar that switches all its gas appliances to efficient electric ones.
The Quote Yard calls November through February peak season across Victoria, and says December is the worst month to discover a fault. Timing therefore does much of the work in keeping a system running. The three jobs below split by season and by the age of the system: a split system service before summer, a gas ducted heater service and duct clean before winter, and repairs, including systems that run on the older R22 refrigerant. Evaporative coolers are outside the services offered here, so the page does not cover them; the jobs below are for refrigerated split, multi-head and ducted systems and for gas ducted heaters.
QuickAir names September and October as the easy months to book if a system is relied on for cooling, and says the first serious heatwave in December fills the diary. Its list of what a full service covers is an indoor coil clean, a drain flush, an outdoor unit clean, operating checks and a refrigerant assessment. The Quote Yard draws the line between a quick visit and a real service: a filter clean and a visual check takes about fifteen minutes, while a proper service covers coil cleaning, electrical testing, drainage checks, control checks and performance measurement. It treats annual servicing as the sensible default, which is guidance, not a regulation, so the unit's own manual comes first. The drain matters most where a head sits upstairs. The same guide says drain pans and lines block with dust and growth over time, and that water then backs up and overflows into the ceiling or down the wall. On a multi-head system each head has its own filter, coil and drain, so each one is opened. Between visits, Mitsubishi Electric advises cleaning the filters every two weeks in peak seasons.
QuickAir suggests March and April for heating work, before the first genuine cold snap in May. A gas ducted heater is serviced by a gasfitter, not an air conditioning technician. Energy Safe Victoria recommends that all gas heaters are serviced at least every two years by a qualified gasfitter, including a test for carbon monoxide leakage, and the Building and Plumbing Commission says gas servicing must follow AS 4575, with the Appendix E checklist and a full servicing record given to the customer within 5 days. Rented homes carry a separate duty: Consumer Affairs Victoria requires a gas safety check every 2 years, and 39.2% of Clifton Hill homes are rented (ABS 2021). Duct cleaning is its own job. The Quote Yard says duct repairs and duct cleaning are separate from a system service, and notes that flexible ducting degrades over decades, joints separate and rodents occasionally damage runs in roof spaces. Mr Duct Cleaning, a Melbourne cleaner, says a duct clean covers the supply and return air ducts, registers, grilles, fans and the air handling unit, using high-powered vacuums and air-pressure tools. It gives every 3 to 5 years as a rule of thumb, and sooner after renovation dust, a musty smell or droppings near the vents.
Some faults are settings. Daikin's troubleshooting guide lists the owner checks first: mode and set temperature, clean filters, nothing blocking the unit, the breaker, and closed windows and doors. It also notes that heating pauses for about 3 to 10 minutes while the outdoor unit defrosts. Where the cause is a leak, the order of work matters. The Quote Yard says a sealed system does not consume refrigerant, so a low charge means a leak, found with electronic detectors, ultraviolet dye or a nitrogen pressure test; a flare joint at the outdoor unit is quick to remake, while a leaking coil often means replacing it. The refrigerant handling code of practice says a system with doubtful integrity must not be recharged until it is repaired and leak tested, and the charge is weighed in to the figure on the data plate. Older systems may run on R22. The Australian Refrigeration Council says R22 imports were largely phased out in 2016, that a small allowance of 2.5 ozone depletion potential tonnes a year can service equipment until 2029, and that recycled or reclaimed refrigerant is used after that. The Quote Yard's rule of thumb is that a repair costing more than about half a new system, on a unit past about ten years, points to replacement. Fault-by-fault detail is under air conditioning repair.


The figures below are indicative ranges from independent Melbourne and Victorian cost guides and installers' published benchmarks, not this business's own prices. They show where a Clifton Hill job is likely to land, and the written quote after inspection gives the actual figure, because the pipe route, the wall, roof access and any heritage or owners corporation step all move it.
whatsthedamage's Melbourne table (updated November 2026) gives supplied and installed prices for five split system sizes: 2.5 kW at $1,250 to $2,625, 3.5 kW at $1,475 to $2,950, 5 kW at $1,900 to $3,675, 7 kW at $2,300 to $4,725 and 9 kW at $3,150 to $5,800. Where the owner has already bought the unit, the same guide puts installation alone at $735 to $1,575. Climate Control Solutions, a Melbourne installer, says a 3.5 kW back-to-back job lands around $2,100 to $2,600, and allows roughly $450 extra for a new circuit and about $250 to remove an old unit. A pipe run from a front room to a rear courtyard is not a back-to-back job, so that installer figure does not apply to it directly. Each install step is set out on the split system installation page.
For several rooms on one outdoor unit, whatsthedamage gives $4,200 to $7,900 for a two-head multi-head system ($5,800 typical) and $7,350 to $12,600 for four heads ($8,900 typical); four heads can serve a living room and three bedrooms on one outdoor unit. For ducted, it splits homes into two bands. A three-bedroom home, or a single-storey four-bedroom home with good roof access, sits at $8,400 to $14,700 ($11,550 typical). Larger homes of four bedrooms and up, two-storey homes, or systems zoned room by room sit at $12,600 to $23,100 ($16,800 typical). With 51.3% of Clifton Hill homes at three bedrooms or more (ABS 2021), both bands apply here, and a freestanding house over two levels falls in the upper one.
whatsthedamage puts an air conditioner service or clean in Melbourne at $105 to $335 per unit ($210 typical) and a ducted system service at $210 to $580 per system. For a gas ducted heater, Climate Control Solutions gives $180 to $320 for a service with no faults. For repairs, The Quote Yard prices callouts by area. Its inner Melbourne figure is $160 to $280 for the callout and $400 to $1,200 for a typical repair total, with the callout usually credited against the repair if it goes ahead; its suburb list, read on 19 November 2026, does not name Clifton Hill, so treat that as the inner-city figure rather than a Clifton Hill rate. The page puts inner-city fees down to parking difficulty and slow travel between jobs. It lists a fitted leak repair and regas at $400 to $900.

Air Conditioning Installation
Split, multi-head and ducted air conditioning installation across Richmond, sized room by room for terraces, apartments and warehouse conversions, with a free written quote after inspection.

Split System Installation
Split system installation in Richmond for wall, floor console and multi-head units, with the outdoor position, pipe route and kilowatt size set out in a written quote.

Ducted Air Conditioning
Ducted air conditioning for Richmond homes: standard, slimline and underfloor systems, zoned room by room, with an itemised written quote after a roof inspection.

Reverse Cycle Air Conditioning
Reverse cycle air conditioning in Richmond sized for winter heating, with gas heater swaps, VEU discount checks and heating kW set out in a written quote.

Hydronic Heating
Hydronic heating in Richmond: radiator panels, in-slab and underfloor pipes, gas boilers and heat pumps, with servicing and a written quote after inspection.

Air Conditioning Repair
Air conditioning repair in Richmond for split, multi-head and ducted systems, with faults traced to the cause and a written quote before any part is ordered.

Emergency Air Conditioning Repair
Emergency air conditioning repair in Richmond for split and ducted systems, booked from 6am to 10pm, seven days, with the callout price confirmed before a technician is sent.

Air Conditioning Service
Air conditioning service in Richmond for split, multi-head, cassette and ducted systems, with filters, coils, drains, outdoor units and refrigerant pressures checked and a written record left.

Aircon Cleaning
Aircon cleaning in Richmond for wall splits and multi-head systems: filters, coil and barrel fan washed into a wash bag, the outdoor coil cleared and airflow tested afterwards.

Ducted Heating
Ducted heating in Richmond: gas ducted heaters from 3 to 6 stars, electric ducted heat pumps, old heater swaps and a written quote after a heat load check.

Ducted Heating Service and Repairs
Gas ducted heating service in Richmond to AS 4575: burners, heat exchanger and flue cleaned and checked, a CO spillage test, faults traced and repairs quoted in writing.

Commercial Air Conditioning
Commercial air conditioning in Richmond for shops, offices and mixed-use buildings: split, cassette, under-ceiling, ducted, packaged and VRF systems, itemised quotes and maintenance contracts.
air conditioning In Clifton Hill
The Quote Yard's servicing guide (published 7 September 2026) gives $140 to $230 for a single split in Melbourne, and across Victoria $180 to $400 for a multi-head system and $250 to $500 for a ducted system. whatsthedamage's Melbourne table puts a service or clean at $105 to $335 per unit, with $210 typical. These are indicative cost-guide figures, not a quoted price. The number of heads, how easily the outdoor unit can be reached and whether a fault turns up during the service set the final figure.
It depends on where the unit goes and how the house is graded. Yarra City Council says a planning permit is normally required for works in a heritage overlay, but its permit-exemption plan (July 2014 version) exempts a residential air conditioner on the rear wall or in the rear setback, or on a side wall set at least 4 metres behind the front facade (2 metres on not contributory properties). Corner properties and places on the Victorian Heritage Register are not covered. Check the property's grading in the council's heritage database and confirm with Yarra City Council on 03 9205 5555 before the unit goes on.
whatsthedamage's Melbourne guide (updated November 2026) puts two-storey homes, larger homes of four bedrooms and up, and systems zoned room by room at $12,600 to $23,100, with $16,800 typical. QuickAir, a Melbourne installer, gives $10,000 to $25,000 and up for large or multi-storey homes. These are indicative ranges. Roof space on each level, the duct route between floors and the number of zones set the actual figure, which is given in a written quote after an inspection.
Yes, for now. The Australian Refrigeration Council says existing R22 units can continue to be serviced with R22, and that there is no need to change a system that is in good working order. A small import allowance for servicing runs until 2029, after which remaining R22 systems will rely on recycled or reclaimed refrigerant. A low charge still means a leak, so the leak is found and repaired before any refrigerant goes back in.
No independent failure-rate ranking was found for this page, so no single brand is named as the most reliable. Daikin states that it was voted the most trusted air conditioner brand for four consecutive years, from 2023 to 2026, in Reader's Digest Australia's Trusted Brands survey, which measures trust rather than breakdowns. Daikin also says a split system can last 10 to 15 years or more with regular maintenance. Installation counts as much as the badge: the Australian Refrigeration Council says the pipework is pressure tested with oxygen-free nitrogen before evacuation, and the refrigerant handling code says the charge is weighed in. Peak Air Conditioning Richmond compares models from several makers at the quote.
Yes. Mitsubishi Electric lists an outdoor operating range for heating down to minus 15 °C on its MSZ-AP split systems, and the Zoned Energy Rating Label shows each unit's heating capacity at two outdoor temperatures so models can be compared. On a cold morning the unit may stop heating for a few minutes: Daikin says this is the outdoor unit defrosting and can take about 3 to 10 minutes. Daikin also suggests floor standing units where heating is a priority, because Daikin says a unit mounted lower warms the lower part of the room more effectively.
GET A FREE QUOTE
BUSINESS
SERVICES
OPERATING HOURS
Sun: 6:00am - 10:00pm
Mon: 6:00am - 10:00pm
Tue: 6:00am - 10:00pm
Wed: 6:00am - 10:00pm
Thu: 6:00am - 10:00pm
Fri: 6:00am - 10:00pm
Sat: 6:00am - 10:00pm