Air Conditioning Repair Richmond, Faults Traced to the Cause

Air conditioning repair Richmond homes need starts with a symptom: a unit running without cooling, water dripping down the wall, a flashing light, a tripped safety switch or a new noise outside. This page explains what each symptom can point to, how a fault is traced, and what Melbourne cost guides put repairs at, from a callout to a compressor. It also covers aircon regas done the licensed way, with the leak found and fixed first, and the repair-or-replace question on older units. Richmond's housing runs from Victorian terraces to high-rise flats, and more than half its homes are rented, so the rules for urgent repairs in rental homes are set out too. Peak Air Conditioning Richmond repairs split, multi-head and ducted systems, with a written quote after diagnosis. Call 0468 046 042 to book a repair visit.

GET A FREE QUOTE

Why Choose Peak Air Conditioning Richmond for Heating and Cooling for Air Conditioning Repair

Peak Air Conditioning Richmond installs, repairs, services and cleans heating and cooling systems across Richmond and 12 nearby suburbs. Two things set out what a buyer gets before any work is booked: a written quote that itemises the job, and one phone line that covers all 12 services from 6am to 10pm. Each trade's work is done under the licence it requires: an ARC refrigerant handling licence for refrigerant work, a licensed gasfitter registered with the Building and Plumbing Commission for gas work, and a licensed electrician, who issues a Certificate of Electrical Safety, for wiring.

Peak Air Conditioning Richmond

Air Conditioning Repair Richmond: Faults in Split, Multi-Head and Ducted Systems

Air conditioning repair in Richmond covers wall splits, multi-head systems that run several indoor heads from one outdoor unit, and ducted systems hidden in the ceiling. The symptom a household notices is rarely the fault itself, so each heading below describes what the symptom can point to and where on this page the fix is explained. Manufacturer troubleshooting guides, such as Daikin's, list several checks an owner can make before a technician is called, and those checks are included where they apply.

Running but Not Cooling or Heating the Room

A unit that runs but leaves the room warm in summer, or cold in winter, has several possible causes. Daikin's global troubleshooting guide asks owners to check the set temperature and mode first, then whether the air filters are clean, whether furniture blocks the air below or beside the indoor unit, and whether windows and doors are closed. It also notes two normal behaviours that can look like faults: warm air takes about three minutes to arrive after heating starts, and heating pauses for about three to ten minutes while the outdoor unit defrosts. The Quote Yard's Victorian repair guide adds that blocked filters, a fouled indoor coil and an outdoor coil packed with leaf litter all mimic failure. Past those, the cause may be electrical, such as a failed capacitor or fan motor, which the fault-finding section covers. A system that cools but will not heat can have a stuck reversing valve, priced in the cost section. Low refrigerant is the last possibility, and the regas section explains why it always means a leak.

Water Dripping from the Indoor Unit

Water running down the wall below a split head is a drainage fault until proven otherwise. Daikin's guide says to stop using the unit, because the water can damage floors and walls, catch the drips, and then check whether water is coming out of the drain hose outside. If nothing is draining, Daikin points to obstructions and bends in the drain hose or drainage path. If the hose is draining but water still drips indoors, a dirty air filter can cause condensate to form and leak from the air outlet. Mitsubishi Heavy Industries' Australian FAQ lists three causes of an indoor leak: a blocked drain pipe, a unit installed so the water cannot run off, or an issue with the refrigeration. Ducted units can lift their water with a drain pump, which Mitsubishi Electric's ducted manual lists among the parts needing service access, and Daikin's malfunction chart gives a drain level fault its own code, with drain clogging, an upward slope or a failed pump or float switch among the listed causes. Water dripping from the outdoor unit is different: Daikin notes that it happens normally during defrost and cooling.

Flashing Lights and Error Codes on the Display

A flashing operation lamp or a code on the controller is the unit reporting a fault it has detected. Daikin's guide gives owners one reset to try: turn the unit off, switch off its dedicated circuit breaker at the switchboard, wait twenty minutes, then switch it back on. Daikin warns not to turn off the main breaker, which cuts power to the whole property, and says that if the light flashes again the unit is likely malfunctioning. On Daikin systems a code is a letter followed by a digit or letter. Its malfunction chart groups A and C codes under the indoor unit, E, F, H, J, L and P codes under the outdoor unit, and U codes under the system. For example, A3 is a drain level fault, A5 can be triggered by a clogged indoor filter, U0 is a shortage of refrigerant and U4 is a communication fault between the indoor and outdoor units. Other brands use their own codes, so the model number and the code shown are the two details worth noting when booking.

Not Turning On or Tripping the Safety Switch

When the unit will not start at all, Daikin's guide lists the simple checks first: whether the breaker has tripped or a fuse has blown, whether there has been a power failure, whether the remote controller's batteries are flat, and whether a timer is set. A unit that refuses to restart straight after being switched off may simply be protecting itself, since Daikin builds in a wait of about three minutes. A safety switch that trips when the air conditioner starts is a different matter. Daikin's advice for a tripping breaker or earth leakage device is to stop using the unit, turn its breaker off and call for service, and The Quote Yard describes repeated tripping as a genuine fault rather than a nuisance. Possible causes range from a failed control board, which that guide says can fail from age, power surges or moisture, to a loose wiring termination or a faulty isolator. Isolator and circuit faults are work for a licensed electrician. In a rental home, a dangerous electrical fault is listed by Consumer Affairs Victoria as an urgent repair.

Rattling, Buzzing or Grinding from the Outdoor Unit

The Quote Yard says mechanical failures tend to announce themselves through noise first. It lists fan motor failure, with symptoms of noise, reduced airflow or a fan that will not run, and fan blade damage, where debris, hail or a blade cracking with age throws the fan out of balance. Daikin's malfunction chart includes an outdoor fan fault whose listed causes include the fan not rotating because something is caught in it. Not every rattle is serious: The Quote Yard notes that a noisy unit may have failed anti-vibration mounts or a loose panel rather than an internal fault, and Mitsubishi Electric's installation manual asks for a rigid wall or support so that operating sound and vibration do not increase. Some sounds are normal. Daikin says a clicking sound can come from the refrigerant control valve or an electrical component switching, and heating can stop with the sound of water flowing while the outdoor unit defrosts. Grinding or a burnt smell is the signal to switch the unit off at its breaker, as Daikin advises, until it has been inspected.

Ducted Zones Not Opening and Weak Airflow at the Vents

Ducted air conditioning moves air through ducts to outlets in each room, with motorised dampers opening and closing zones. Mitsubishi Electric's ducted page says its Zone Controller can create up to 4 or 8 zones, while its May 2026 brochure lists 4 and 10 zone models with either on/off or linear damper motors. When one zone stays shut or one room gets little air, possible causes include a damper motor that no longer drives, a controller or wiring fault, or a duct problem in the roof. The Quote Yard notes that zone motors, controllers and dampers each add a potential failure point, that crushed ducting in the roof affects one room only, and that rodent damage turns up in both ducting and wiring. Weak airflow across every outlet can point instead to a clogged return air filter or a blocked return path, and YourHome describes a return air path from every outlet back to the central system as important. The same brochure describes an air balance setting, which the installer uses to set the maximum opening of each zone damper, so an airflow complaint can also come down to how the system was balanced.

Clifton Hill Emergency Air Conditioning Repair
Carlton Emergency Air Conditioning Repair

Peak Air Conditioning Richmond

Fault Finding on Every Air Conditioning Repair

Fault finding follows an order: the simple causes that mimic a breakdown are ruled out before parts are blamed, then the electrical supply and controls are tested, and the repair is proven in both modes before the job is signed off. The three steps below describe that general practice. They are standard trade method rather than a manufacturer's repair procedure, and where a manufacturer's manual gives a matching check, it is named.

Checking Filters, Coils and Airflow First

The first checks on arrival are the ones that cost least to fix. The Quote Yard says cleaning and servicing resolve more complaints than any actual repair, because blocked filters, a fouled indoor coil, an outdoor coil packed with leaf litter and a blocked condensate drain all produce symptoms that look like failure. Daikin's malfunction chart shows the same link from the other direction: one of its indoor codes lists a clogged air filter among the causes. So the technician looks at the filters, the indoor coil face and the outdoor coil, checks that nothing blocks the inlet or outlet of either unit, and confirms that air is leaving every outlet. A visual check also looks for oil or dust staining on pipe joints, which the Australian Refrigeration Council's code of practice lists as a sign of a refrigerant leak. If the cause turns out to be dirt rather than a failed part, the fix belongs to a full air conditioning service or a deep aircon cleaning rather than a repair.

Electrical Testing from the Isolator to the Outdoor Unit

If airflow is not the cause, the electrical path is tested next, starting at the outdoor isolator and working through to the outdoor unit's components and the indoor control board. As general practice, that means confirming supply voltage at the isolator, checking the cable between the indoor and outdoor units, and testing the capacitor, contactor and fan motors. Daikin's malfunction chart shows why the interconnecting cable matters: its code for a communication fault between the indoor and outdoor units lists wrong wiring, a short circuit in that wiring, and the outdoor unit's power being off among the causes. The Quote Yard adds that wiring terminations loosen over a decade of heating and cooling cycles until they arc or lose contact. Manufacturers set a benchmark for the insulation check: Mitsubishi Electric's ducted installation manual asks for a 500 V megohmmeter reading of at least 1.0 MΩ before the unit runs. Any fault found in the circuit, the switchboard or the isolator itself is passed to a licensed electrician.

A Test Run in Cooling and Heating Before Sign-Off

A repair is only finished when the system has been run and seen to work in both modes. Manufacturers describe how: Mitsubishi Electric's split system manual starts a test run from the emergency switch, pressed once for cooling and twice for heating, and the test runs for 30 minutes. Its ducted manual lists what the test run checks: cool air in cooling mode, warm air in heating mode, and the fan speed changing when it is changed on the controller. On a repaired system the same checks are used as general practice, and the technician also confirms that the fault code has cleared and that the condensate drains away. Two normal behaviours are allowed for during the run. Mitsubishi Electric notes the compressor will not restart for 3 minutes after a stop, to protect the air conditioner, and Daikin notes heating can pause for a defrost. Running both modes matters on a reverse cycle system, because a fault such as a sticking reversing valve can leave one mode working and the other not.

Peak Air Conditioning Richmond

Why Richmond Households Call Peak Air Conditioning Richmond for Repairs

Licensed air conditioning repair rests on three things a household can check: the refrigerant licence, a written quote before any part is ordered, and the right electrical paperwork when wiring is replaced. Peak Air Conditioning Richmond takes repair bookings from 6am to 10pm, seven days. That spread of hours suits a suburb where the ABS 2021 Census counted 54.7% of homes as rented, against 28.5% across Victoria, because a tenant, a property manager and an owner often all need to agree on a time.

ARC Refrigerant Handling Licence for Any Work on the System

The Australian Refrigeration Council's rule is direct: any person who handles refrigerant or works on refrigeration and air conditioning equipment must hold a refrigerant handling licence. The council defines handling to include servicing and maintaining that equipment whether or not refrigerant is present, so a repair inside a split system is licensed work even when the gas circuit is never opened. Any regas, leak repair, reversing valve or compressor replacement opens the circuit, and that work must follow the council's code of practice, which is referenced in a Determination under the Ozone Protection and Synthetic Greenhouse Gas Management Regulations 1995. Mitsubishi Electric states the same requirement in its buying guide, saying that any person installing or servicing air conditioning equipment must hold a refrigerant handling licence. Refrigerant work on a repair is done under the ARC licence it requires. The practical step for a household is to ask for the licence number, which can be checked, and to keep it with the quote and invoice.

A Written Repair Quote After Diagnosis, Before Parts Are Ordered

Diagnosis and repair are two separate steps, and The Quote Yard's guide says a household is entitled to decide between them. A written repair quote is given once the fault has been found, and before any part is ordered. It names the fault and how it was confirmed, the part to be fitted with its part number, the cost of the part shown separately from labour, and whether the callout fee is credited against the repair. The Quote Yard says that credit is usual when the repair goes ahead. The part number matters because some parts, such as control boards, are made for one model, and their availability can decide whether a repair is possible at all. Ordering only after the quote is accepted also avoids a wasted second visit, which The Quote Yard says is usually charged when a part has to be ordered rather than carried on the van. A written quote can also be checked against a second opinion before any money is spent.

A Certificate of Electrical Safety When the Circuit or Isolator Is Replaced

Some repairs reach past the air conditioner into the home's fixed wiring, such as replacing a failed outdoor isolator, the circuit feeding the unit, or its breaker at the switchboard. That is electrical installation work, done by a licensed electrician, and Energy Safe Victoria requires a Certificate of Electrical Safety for it under the Electricity Safety Act 1998. The electrician must give the customer a copy, within 30 days for non-prescribed work, which Energy Safe Victoria defines as all electrical installation work other than the prescribed categories. Prescribed work must also be inspected by a licensed electrical inspector. Because the certificate is tied to installation work, not every air conditioner repair produces one, and the electrician states whether a certificate applies to the job. The certificate is worth filing with the system's paperwork in a rental home, because Consumer Affairs Victoria requires rental providers to have electrical installations checked by a licensed or registered electrician every 2 years.

Abbotsford Emergency Air Conditioning Repair
Carlton Emergency Air Conditioning Repair

Peak Air Conditioning Richmond

What Air Conditioning Repair Costs in Richmond

The figures below come from independent cost guides. The main source is The Quote Yard's Victorian air conditioning repairs guide, published 7 September 2026, which describes its prices as indicative 2026 Victorian estimates. They are market ranges, not Peak Air Conditioning Richmond's price list. The final figure depends on the part, the brand, its availability, the system's age and how easy the units are to reach, and a written quote is given after diagnosis.

Callout and Diagnosis Fees in the Inner Melbourne and CBD Band

The Quote Yard prices callouts by area, and its Inner Melbourne list names Richmond, so the Inner Melbourne and CBD band applies: a callout fee of around $160 to $280, with a typical repair total of $400 to $1,200 including parts. Across Victoria the same guide puts attendance and diagnosis at $120 to $250, and says the callout is usually credited against the repair if it proceeds. Businesses that charge by the hour instead run at about $110 to $180 per hour with a minimum charge. The guide explains why the inner band sits higher: inner-city attendance involves parking difficulty and slow travel between jobs, and apartment work adds building access on top. As a cross-check, whatsthedamage.com.au's Melbourne table, updated November 2026, puts a minor air conditioning repair at $160 to $525 per job. Attendance outside standard hours costs more. The Quote Yard says after-hours attendance carries a premium of fifty to one hundred per cent, with public holidays higher again, and urgent call-outs are covered under emergency air conditioning repair.

Capacitor, Contactor, Fan Motor and Control Board Prices

The Quote Yard says capacitors, contactors and fan motors cover a large share of Victorian callouts, and it lists these fitted prices for Victoria: a capacitor at around $180 to $400, a contactor at $200 to $450, a fan motor at $450 to $900 and a control board at $500 to $1,400. The capacitor stores and releases energy to give the motors their starting torque, and the contactor is the heavy-duty switch that energises the outdoor unit. The guide calls both wear items, with failures clustering around eight to twelve years on most systems, and says the work on either takes under an hour. Fan motors are model specific, so the price depends partly on availability. Control boards are the widest range because each is a manufacturer-specific part, and The Quote Yard advises asking for the part number and checking availability before agreeing. For comparison, hipages' national repair guide, updated 6 January 2026, puts a circuit board replacement at $120 to $600, which is a national figure and runs below the Victorian range.

Reversing Valve and Compressor Replacement Prices

The two most expensive repairs sit in the refrigerant circuit. The Quote Yard puts a reversing valve replacement at around $700 to $1,500 in Victoria. The valve only exists on reverse cycle systems, where it sends refrigerant one way for cooling and the other way for heating, and the price reflects the work: the refrigerant is recovered, a new valve is brazed in, and the system is recharged. The guide adds that Victorian reverse cycle systems run far more hours heating than cooling, which loads the reversing valve, so its failures are correspondingly more common here. A compressor replacement is listed at $1,400 to $2,800 fitted, the top of the Victorian repair range. On top of the part itself, the figure for either job moves with the refrigerant type, the size of the system and the access to the outdoor unit. The Quote Yard notes that roof-mounted plant costs more to attend than a ground-level split, a point that matters in a suburb where the ABS 2021 Census counted 53.0% of homes as flats or apartments.

Leak Repair and Regas Prices

The Quote Yard puts locating a refrigerant leak, repairing it and recharging the system at around $400 to $900 in Victoria, and says where the leak sits drives most of that range. An accessible flare joint at the outdoor unit is at the low end, while a leak in a buried pipe run or inside a coil costs more. whatsthedamage.com.au's Melbourne table puts a major repair or regas at $315 to $1,250 per job. Two other figures are sometimes quoted. QuickAir, a Melbourne installer, lists refrigerant leak repair from $165 on its September 2026 pricing guide, and hipages' national guide puts replacing refrigerant at $160 to $400 and fixing leaks at $225 to $1,600. Both hipages ranges are national averages rather than Melbourne figures. None of these prices includes a top-up without a leak search, because the refrigerant code of practice does not allow a known leaking system to be topped up, which the regas section explains.

Peak Air Conditioning Richmond

Repair or Replace an Older Air Conditioner

Every repair quote on an older system raises the same question: is it worth spending money on this unit, or is the money better put towards a new one. Two facts usually settle it, the system's age and the size of the repair compared with a new system, and both can be read before any work is approved. The Quote Yard says the system's age and refrigerant type both sit on the data plate on the outdoor unit.

Unit Age Against a 10 to 15 Year Lifespan

The 10 to 15 year figure is Daikin's own claim, not an industry standard. Daikin's Australian split system page says that with regular maintenance and servicing a Daikin split system can last 10 to 15 years or more, and its ducted page gives the same range for its ducted systems with proper care. Other makers publish their own figures or none. Age matters to a repair decision in two ways. First, wear: The Quote Yard says capacitors and contactors tend to fail around eight to twelve years, refrigerant leaks develop as joints and coils age, and the compressor usually fails last if it fails at all. Second, parts: manufacturers support a model for a period after it leaves the market, and the same guide says that from about twelve years a part may need a compatible substitute or may not be available. The guide calls capacitor and contactor replacement worth doing on any system with life left in it, while a major repair on a unit near or past its expected age is worth weighing against replacement.

When a Compressor Quote Approaches the Price of a New Split System

The compressor is the part whose failure most often ends a system's life, and The Quote Yard gives a rule of thumb for the decision. Where a repair exceeds roughly half the cost of a new system and the unit is past about ten years, replacement is usually the better choice. Below either threshold, repairing is generally sensible. The same guide says a compressor replacement on a unit past eight or ten years approaches or exceeds the cost of a new system, so the repair quote is best read beside a supply-and-install price for a new unit of the same size, which the air conditioning installation page sets out, along with older R22 systems and the 2029 refrigerant cut-off. The guide also says compressors rarely fail without a cause, such as years of running undercharged, short cycling or blocked airflow, and that replacing the compressor without fixing the cause repeats the outcome. On a new unit, the manufacturer warranty applies when it is installed to the manufacturer's requirements.

Abbotsford Emergency Air Conditioning Repair
Carlton Emergency Air Conditioning Repair

Peak Air Conditioning Richmond

Aircon Regas and Refrigerant Leak Repairs in Richmond

An aircon regas means putting refrigerant back into a system that has lost some. Done properly it is the last step of a leak repair, not a job on its own, and the steps below follow the Australian Refrigeration Council's code of practice, the national rules licensed technicians must observe. Older R22 systems face an extra constraint: the council says existing R22 units can continue to be serviced with R22, but after 2029 their maintenance will rely on recycled or reclaimed refrigerant.

Low Refrigerant Means a Leak, Not a Top-Up

Refrigerant is not used up as the system runs. The Quote Yard's guide puts it plainly: a sealed system does not consume refrigerant, so a low charge means a leak exists, and recharging without finding it means paying again next season. The council's code turns that into a rule. A system known to be leaking must not be topped up with refrigerant until all leaks are fixed, and a technician cannot do other work on leaking equipment without repairing the leak. Where the system's temperatures and pressures point to a low charge, the code requires a leak tightness test, and where a technician doubts a system's integrity from its leakage rate and charging history, it must not be recharged until repairs and leak testing are done. A top-up without a leak search can look cheaper on the day, but the refrigerant escapes again, which is the emission the licensing scheme exists to prevent. That is why the regas price on this page is listed together with finding and fixing the leak.

Leak Tracing at Flare Joints, Valves and Coils

The council's code describes leak tracing in three parts: a visual inspection, a check of operating temperatures and pressures against the manufacturer's data, and a leak inspection with a detector. The visual check looks for oil or dust stains on joints, components or insulation. The detector must suit the refrigerant, and R32, the refrigerant in Mitsubishi Electric's MSZ-AP splits and most Daikin ducted systems, carries an A2L safety class in the code's refrigerant table, a lower-flammability class, so the code calls for a detector designed for combustible gases. It lists the common leakage points: flare and brazed joints, Schrader and service valves, and corroded areas and return bends on the indoor and outdoor coils. Manufacturers agree on the weak spot: Mitsubishi Electric's ducted manual names defective flaring as the main cause of gas leakage, and its split system manual warns that an over-tightened flare nut can crack after a long period and leak. The code recommends an electronic detector to search an area and a leak spray to confirm the exact spot, and it warns that the first leak found may not be the only one.

Recharging by Weight to the Nameplate Charge

Once the leak is repaired, the system is pressure tested with nitrogen, evacuated and only then recharged, because the code says a system must not be recharged before it has been fully leak tested, all leaks repaired and the system evacuated. Mitsubishi Electric's split system manual sets the evacuation target at 500 microns. The recharge itself is done by weight. The code says refrigerant must be weighed into and out of a system, that the system must not be overfilled, and that it should be recharged to the quantity shown on its identification plate. Where the pipe run is longer than the factory charge allows for, the manufacturer adds an allowance: Mitsubishi Electric's MSZ-AP manual specifies 20 g of R32 per metre beyond the chargeless length, which is 10 m on its 2.5 to 4.2 kW models. The same manual says to charge slowly with liquid refrigerant. Overcharging is a fault in its own right, and Daikin's malfunction chart has a code for abnormal high pressure or an overcharged system.

Peak Air Conditioning Richmond

Air Conditioner Repairs in Richmond Apartments and Rental Homes

Richmond's housing shapes how a repair is reached and who arranges it. The ABS 2021 Census counted 53.0% of occupied dwellings in Richmond as flats or apartments and 54.7% as rented. Wikipedia describes a suburb mixing converted warehouse residences, such as The Malthouse, public housing high-rise flats and Victorian-era terraces. The two headings below cover the access side of a repair in a block of flats and the rules that apply when a rented home loses heating or cooling.

Outdoor Units on Balconies, Rooftops and Plant Decks

In an apartment, the outdoor unit may sit on the balcony, on the roof or on a shared plant deck, and where it sits decides how a repair is reached. The Quote Yard notes that apartment work adds building access to inner-city callouts, and that roof-mounted plant costs more to attend than a ground-level split. Where the unit is on a roof or plant deck, access may need the building manager's help, so the booking notes the floor, where the outdoor unit is and how the roof or plant area is opened, and the arrangement is confirmed before the visit. Mitsubishi Electric's manual asks that a unit installed at height has its legs secured, which is checked when a rattle is traced. On a balcony, Daikin's guide lists objects blocking the outdoor unit's air inlet or outlet among the causes of a unit stopping with a flashing lamp, so stored items, screens or plants close to the unit are moved before anything else is tested. Daikin also markets VRV systems, such as its VRV IV W, for high-rise residential buildings with limited plant space, and where a building runs central plant of that kind, the fault may sit in shared equipment rather than in one apartment's unit.

Urgent Repairs When a Rented Home Loses Heating or Cooling

Consumer Affairs Victoria's rental repairs page, last updated 27 February 2026, lists urgent repairs that a rental provider must make immediately. The list includes an essential service or appliance for heating that is not working, a cooling appliance or service provided by the rental provider that is not working, and a dangerous electrical fault. The rental provider must organise and pay for all repairs that are not the renter's fault. The renter should contact the rental provider or agent straight away, using the emergency number given at the start of the tenancy, and confirm the request in writing. If there is no prompt response, the renter may arrange an urgent repair themselves, but only when it costs $2,500 or less, and the rental provider must repay them within 7 days of a written notice with receipts. Work needing a licence must be done by a qualified person. A written quote naming the fault and its cost gives both parties the record that process relies on. For heating, landlords should also check Consumer Affairs Victoria's current minimum standards, which require a fixed heater in good working order in the main living area.

Abbotsford Emergency Air Conditioning Repair

TESTIMONIALS

What Our Air Conditioning Repair Customers Say About Us

The Process

3 Step Process For Your Air Conditioning Repair Needs

Call or Book Between 6am and 10pm

Call the one number any day between 6am and 10pm. The booking notes the system type, the fault or the job, the address, who needs to be present (owner, tenant, agent or building manager) and any building access rules. Same-day visits are arranged where possible.

Inspection and Written Quote

A technician inspects the site and the existing system or the planned unit positions, then gives a written quote listing equipment, labour, extras and old unit removal. For repairs, the diagnosis comes first and any part is quoted before it is ordered. Work starts once the quote is accepted.

Installation or Repair, Testing and Handover

Each trade works under the licence it needs: ARC for refrigerant, a BPC-registered gasfitter for gas and a licensed electrician for wiring. The system is then tested, the controls are explained, and paperwork such as a Certificate of Electrical Safety or a gas compliance certificate is handed over where the job requires one.

FREQUENTLY ASKED QUESTIONS

Air Conditioning Repair In

Everything you need to know about our Air Conditioning Repair In

How much does air conditioning repair cost in Richmond?

Richmond sits in The Quote Yard's Inner Melbourne and CBD band, where a callout runs at around $160 to $280 and a typical repair total, including parts, at $400 to $1,200. The callout is usually credited against the repair if it goes ahead. Individual parts range from a capacitor at around $180 to $400 fitted to a compressor at $1,400 to $2,800. These are indicative 2026 Victorian estimates, and a written quote is given after the fault has been diagnosed.

Why is my AC running but not cooling?

Start with the checks Daikin's troubleshooting guide lists: the mode and set temperature, clean filters, nothing blocking the indoor or outdoor unit, and windows and doors closed. The Quote Yard notes that blocked filters, a fouled coil or an outdoor coil packed with leaf litter all mimic a breakdown. If those are fine, possible causes include a failed capacitor or fan motor, or a refrigerant leak. Low refrigerant always means a leak somewhere, so it is fixed by finding and repairing the leak, not by topping up.

Why is my air conditioner leaking water inside?

Water inside is usually a drainage problem. Daikin's guide says to stop using the unit, catch the water and check whether the drain hose outside is discharging. No water outside points to a blocked or kinked drain path, while water draining outside and inside together can point to a dirty filter causing condensate to leak from the air outlet. Mitsubishi Heavy Industries also lists a unit installed so the water cannot run off, or an issue with the refrigeration, as possible causes.

Is it worth repairing an old air conditioner or should I replace it?

The Quote Yard's rule of thumb is to replace when a repair costs more than roughly half the price of a new system and the unit is past about ten years, and to repair below either threshold. Daikin says its own split systems can last 10 to 15 years or more with regular maintenance, which gives one brand's reference point for age. Parts availability also counts, since boards for older models can become hard to find. Peak Air Conditioning Richmond sets the repair quote out in writing so it can be compared with the price of a new unit.

Does an air conditioner need regassing, or does low gas mean a leak?

An air conditioner does not use up its refrigerant, so low gas means there is a leak. The Australian Refrigeration Council's code of practice says a system known to be leaking must not be topped up until all leaks are fixed. A proper regas therefore follows a leak search, the repair, a pressure test and evacuation, and the refrigerant is then weighed in to the quantity on the unit's identification plate. A top-up alone would leak away again.

Who pays for air conditioner repairs in a rental property in Victoria?

Consumer Affairs Victoria says the rental provider must organise and pay for all repairs that are not the renter's fault. A heating appliance that has stopped working, or a cooling appliance supplied by the rental provider, is an urgent repair that must be made immediately. If the rental provider does not respond promptly, the renter can arrange an urgent repair of $2,500 or less and be repaid within 7 days of giving written notice with receipts. If the renter caused the damage, the renter may have to pay.

Request A Free Air Conditioning Repair Quote

GET A FREE QUOTE