Ducted Heating Service Richmond, Safe Warmth Through Every Winter

A ducted heating service Richmond households can book covers the gas ducted heater, its flue and the ducts that carry the warm air. Gas servicing in Victoria must follow AS 4575, and the Building and Plumbing Commission says its Appendix E checklist includes carbon monoxide testing. Peak Air Conditioning Richmond has gas ducted heaters serviced by a licensed gasfitter registered with the Building and Plumbing Commission and endorsed for Type A appliance servicing. The service cleans and checks the burners, ignition, fan and heat exchanger, tests for gas leaks and CO, and runs the heater through a full heating cycle. Faults found on the day are traced, and repairs are quoted in writing before work starts. With 54.7% of Richmond dwellings rented in the ABS 2021 Census, the servicing record matters to landlords and tenants too. Bookings run from 6am to 10pm, seven days. Call 0468 046 042.

GET A FREE QUOTE

Why Choose Peak Air Conditioning Richmond for Heating and Cooling for Ducted Heating Service and Repairs

Peak Air Conditioning Richmond installs, repairs, services and cleans heating and cooling systems across Richmond and 12 nearby suburbs. Two things set out what a buyer gets before any work is booked: a written quote that itemises the job, and one phone line that covers all 12 services from 6am to 10pm. Each trade's work is done under the licence it requires: an ARC refrigerant handling licence for refrigerant work, a licensed gasfitter registered with the Building and Plumbing Commission for gas work, and a licensed electrician, who issues a Certificate of Electrical Safety, for wiring.

Peak Air Conditioning Richmond

Ducted Heating Service Richmond: Gas Ducted Heaters and Their Ducts

A gas ducted system is two parts working together: the heater, where gas burns and a fan moves household air past a heat exchanger, and the network of ducts that carries the warm air to each room and draws it back again. Energy Safe Victoria notes that any gas heater can spill carbon monoxide, central heating units included, which is why the heater side of the job is regulated gas work. The three parts below cover the heaters that are serviced, how the heater's location shapes the visit, and where duct cleaning fits alongside the service.

Gas Ducted Heating Service for Brivis, Rinnai and Braemar Heaters

Brivis, Rinnai and Braemar are three of the names a Richmond household may find on its heater's data label, and two of them now belong together. Brivis ducted gas heaters are sold by Rinnai Australia, whose current Brivis range includes the StarPro 6, 5 and 4, the Buffalo BX5C and BX3C, the Classic Compact and the Classic Wombat, and Rinnai publishes the Brivis error code sheet that owners use when a heater stops. Brivis's operation manual for those models says the heater should be serviced at two-year intervals by personnel trained on them, and it lists the work: clean the burners, check and adjust the ignition system, check and clean the fan assembly, check and clean the heat exchanger, and check the gas supply flow and lock-up pressure. Newer StarPro and Buffalo controllers flash a spanner symbol with a message that fan run hours indicate it is time for a service call. Braemar is a Seeley International brand whose range includes ducted gas heating and ducted add-on cooling, and a Braemar heater is serviced to Braemar's own instructions rather than to a Brivis schedule. The make, model and serial number go on the servicing record, so the right manual is used for the heater in the house. Brands are named here as plain facts, and whether a particular older model can still be serviced and supplied with parts is confirmed when the heater is booked in.

Roof-Space, Underfloor and External Cabinet Heaters: Access on Service Day

Where the heater sits decides how the technician reaches it, and Brivis's manuals treat access as part of the installation rather than an afterthought. The Classic installer's manual states that all service clearance measurements must be kept, because anything less impedes the serviceability of the heater, and the operation manual says every heater needs safe and reasonable access, with some installations needing two service personnel to meet health and safety requirements. A roof-space heater is reached through the ceiling hatch and along the walkway and platform the installer built, so clearing stored boxes from the hatch and walkway before the visit saves time. An underfloor heater is reached through the subfloor access opening, which needs to be unobstructed. An external cabinet heater sits outside on its pad, and the operation manual asks owners to stop plants and weeds growing around it, keep its recommended clearances and watch for water building up around the unit. Homeupkeep's Melbourne guide notes that external cabinet units are the cheapest to service. Wikipedia describes most Richmond houses as single-fronted Victorian homes on long, narrow blocks, where a tight side path or a low subfloor can add time on site, so the heater's location is noted when the service is booked. Choosing where a new heater should go is a separate question, covered with replacements.

Ducted Heating Cleaning: Ducts, Outlets and Return Air Grilles

Ducted heating cleaning is a different job from a heater service, and the sources keep the two apart. The Quote Yard's Victorian servicing guide states that duct repairs and duct cleaning are separate jobs from a system service, while Climate Control Solutions prices a gas ducted service with a deep clean of the return air and ductwork as its own, dearer line. The cleaning job covers the duct runs, the outlet in each room and the return air grille that feeds air back to the heater. Brivis's operation manual recommends having the ducting cleaned every 3 years, and asks owners to check any return air filter fortnightly and clean it at least every two weeks through the heating season, because a blocked filter significantly affects the heater's performance and efficiency. Between professional cleans, Better Health suggests vacuuming out duct registers and cold air return vents with the heater off and cool. Brivis also notes that fumes from candles, fragrant oil burners, cooking or smoking can be drawn into the system and stain the area around the outlets, especially where the return air grille is in the ceiling. Where add-on cooling shares the same ducts, the cooling side is serviced as air conditioning, as set out on the air conditioning service page. Duct cleaning prices are in the cost section below.

Peak Air Conditioning Richmond

What a Gas Ducted Heater Service Includes Under AS 4575

The Building and Plumbing Commission states that gas servicing work in Victoria must be carried out in accordance with AS 4575, and that Type A servicing includes internal cleaning, maintenance and adjustment of the appliance, as well as the adjustment, repair or replacement of a component. Brivis's two-yearly Service Maintenance Schedule shows what that means on a ducted heater, from wiring, fan motors and overheat switches to burners, gas pressures, the CO level and the sequence of operation. The four parts below take the main checks in turn. Model figures such as burner pressures come from each heater's own data label and manual, so none is quoted here.

Burner, Heat Exchanger and Flue Inspected and Cleaned

The burners, heat exchanger and flue make up the heater's combustion path, and Brivis lists all three on its service schedule. The burners and injectors are cleaned and checked, along with the spark igniter and flame sensor that light the gas and prove the flame. Brivis's service manual has the technician clean the igniter probe, check its lead and plug, and confirm that the flame sensor rod is clean and correctly positioned. The heat exchanger is checked and cleaned; as a general rule of how gas ducted heaters work, it is the part the burner heats and the fan blows household air across, keeping the burning gas apart from the air sent to the rooms. On the flue side, the service manual reads soot marks on the flue terminal or flue pipe as a sign of poor combustion or a possibly blocked heat exchanger, and has any build-up of soot or silicon in the combustion fan housing or flue pipe cleaned out. The schedule also covers the combustion air intakes, the flue termination and the cowl. Energy Safe Victoria lists a partly or totally blocked flue among the causes of high carbon monoxide levels, and Better Health recommends that professional servicing includes an inspection of the flue. The owner's part is simple: Brivis asks that the flue terminal is never hosed and is kept clear of plant growth.

Carbon Monoxide Spillage Test on Every Service

Because gas servicing in Victoria must follow AS 4575, the carbon monoxide test is part of the service itself rather than an optional extra. The Building and Plumbing Commission describes the AS 4575 Appendix E checklist as including carbon monoxide testing, and Energy Safe Victoria says a qualified gasfitter will inspect the heater and check its installation, including testing for CO leakage. Better Health puts it the same way: every type of gas heater, central heating units included, should be serviced at least every two years and tested for carbon monoxide spillage. Brivis's Service Maintenance Schedule gives the result a line of its own, the CO level in parts per million at each two-yearly service, recorded beside the gas pressures and outlet temperatures. That turns the test into a reading the household can see on paper and compare from one service to the next, rather than a box ticked out of sight. Better Health also advises asking, before booking, whether the gasfitter has the right equipment and has completed training on detecting and fixing carbon monoxide spillage risks. Some cost guides list a service with a CO test as a separate price, so it is worth checking that the written quote names the test, as the cost section explains.

Gas Leak Test and Burner Adjustment

A gas leak test and a burner pressure check are the two adjustments that keep a heater burning the way its maker intended. The Building and Plumbing Commission's rental gas safety check includes testing all gas appliances for leakage, and Brivis's installer's manual describes the method at the heater: once the pressure test points are closed again, the joints are tested for leaks with a soapy water solution or a leak detector spray. The burner check uses a manometer on the gas valve's test points. Brivis has the inlet pressure read while the other gas appliances in the house run at full capacity, and the burner pressure confirmed against the figure printed on the appliance data label, then adjusted at the gas valve's regulator if it is out. The service schedule records the flowing inlet pressure and the burner pressure at high rate, and at low rate on modulating models, and the operation manual adds a check of the lock-up pressure. Brivis's service manual explains why this matters: low inlet pressure can cause unreliable ignition and reduced heat output, and a gas valve that cannot be set to its specified pressures has to be replaced. No pressure figure is given on this page, because each model's figure is printed on its own data label.

Thermostat and Fan Operation Tested Through a Full Heating Cycle

The last part of a service is watching the heater work from start to finish. Brivis's service schedule lists the thermostats, any zone controls, the sequence of operation, the return air temperature and the outlet air temperature at the register closest to the heater. In a normal start, the operation manual says the burners run for about a minute before the fan comes on, so that the first air reaching the rooms is already warm. Brivis's installer's manual sets the checks for a running heater: the fan keeps running while the burners operate, and the warm air at any outlet is no more than 45 °C above the return air temperature. The heater is then switched off at the thermostat to confirm that both the burners and the fan shut down. Brivis's service manual treats a 47 °C rise between room air and the nearest outlet as a true overheat, and its operation manual says repeated overheating is typically caused by insufficient airflow, so the temperature readings point the technician towards filters, outlets or ducts before any part is blamed. On a zoned house, the schedule's zone operation line covers the zones; as general practice, each one is selected from the controller and checked for air. A heater that passes every step has been seen to light, heat, cycle and stop, not just to start.

Peak Air Conditioning Richmond

Why Choose Peak Air Conditioning Richmond for Gas Ducted Heating Service

A gas ducted heating service is only as sound as the licence behind it and the paperwork left after it. The three parts below set out what a Richmond household can check for itself: the gasfitter's servicing class, the record handed over after the visit, and how faults and repairs are handled. Bookings run from 6am to 10pm, seven days, which helps in a suburb where an owner, an agent and a tenant may all need to agree on a time.

The Type A Servicing Class on the Gasfitter's Licence Card

In Victoria, a gas ducted heater is a Type A appliance: Energy Safe Victoria classes domestic central heaters with cookers, space heaters and water heaters under the Gas Safety Act 1997. The Building and Plumbing Commission then limits who may service one, stating that only plumbers registered or licensed in the specialised class of Type A appliance servicing can carry out Type A appliance gas servicing work. Its general gasfitting class lists preparing, installing and commissioning Type A appliances, while servicing sits in that separate specialised class. Peak Air Conditioning Richmond has its gas ducted heating service work carried out by a licensed gasfitter registered with the Building and Plumbing Commission and endorsed in the Type A servicing class. A household does not have to take that on trust. Energy Safe Victoria suggests asking to see the gasfitter's licence card and checking the registered classes printed on its back, and Better Health notes that a registered or licensed tradesperson carries a photo ID card stating the kinds of work allowed, which can also be checked on the commission's website. Brivis's operation manual sets the same expectation from the manufacturer's side: its heaters are to be serviced only by an authorised person holding the licensing the state gas regulator requires, who issues any compliance certificates for the work.

The Completed AS 4575 Servicing Record Within Five Days

The servicing record is the household's proof of what was done. The Building and Plumbing Commission requires the gasfitter to give the customer a copy of the complete gas servicing record, including the completed AS 4575 Appendix E gas appliance servicing checklist, within 5 days, and to keep it for 10 years. The record identifies the heater by make, model, model number, gas type and serial number, so it belongs to that appliance and not just to the address. Brivis's maintenance schedule shows the kind of detail a ducted heater service produces: gas inlet and burner pressures, the CO level in parts per million, return and outlet air temperatures, and an action code against each item, running from inspected and working, through adjusted, cleaned, replaced and repaired, to referred to the installer. Kept together, those records give a heater a history from one service to the next. That history helps when a fault appears, when a house is leased or sold, and when a repair has to be weighed against replacement, because it shows whether the same problem keeps returning. For a rented home, the same paperwork supports the rental provider's two-yearly gas safety check, which is covered in the carbon monoxide section.

Unsafe Faults Made Safe Straight Away, Repairs Quoted in Writing

Two rules govern what happens when a service turns up a problem. The first comes from the Building and Plumbing Commission: a safety-critical non-compliance, such as a gas leak, spillage of combustion products, or overheating or scorching of surfaces, must be made safe at the time by repairing, isolating or disconnecting the appliance, and if the customer does not consent, the gasfitter must notify Energy Safe Victoria. In practice that means a heater found to be spilling may be left disconnected until it is fixed, even in the middle of winter, and the reason is explained to the household on the day. The second rule is the business's own: every other repair is quoted in writing before work begins. The quote names the fault found, the part, the labour and any further checks, so an owner or a rental provider can approve it before money is spent. Once the quote is approved, the repair can go ahead. Where the fault is simple and the part is on hand, that may happen on the same visit; otherwise a return visit is booked for when the part arrives. Brivis's service manual itself works in this order, testing each likely cause in turn before a part such as a gas valve or control board is changed.

Peak Air Conditioning Richmond

What Ducted Heating Service and Repairs Cost in Richmond

The figures below come from Melbourne cost guides and installer price pages published in 2026. They are indicative ranges, not the business's own prices, and the real figure comes from a written quote once the heater has been seen. No source read for this page publishes a standard-hours call-out fee for gas ducted heater repairs. The nearest published figure is general: The Quote Yard's Victorian gas fitting page says most Victorian gas fitters charge a call-out fee of $80 to $130 and an hourly rate of $90 to $140, but that covers gas fitting work in general, such as appliance connections, and is not a ducted heater repair price.

Gas Ducted Heating Service Prices With and Without a CO Test

Climate Control Solutions, a Melbourne installer, puts a gas ducted heating service at $180 to $320 where no faults are found, in a guide dated 4 August 2026. Homeupkeep's Melbourne gas ducted guide, updated 14 June 2026, lists a standard service with no faults at $220 to $320 and a service plus CO test at $280 to $380. The gap between those two homeupkeep rows is the reason to read any quote closely. The Building and Plumbing Commission describes the AS 4575 Appendix E checklist as including carbon monoxide testing, so a service done to that standard includes the test, and the written quote should say so rather than leave it implied. Homeupkeep also lists an annual service contract at $180 to $280 a year, an option some households may prefer to booking each service separately, although Energy Safe Victoria's own recommendation is a service at least every two years. Within each range, the price moves with the heater's location and access, its age and condition, and whether the visit uncovers a fault that needs more time. A service that turns into a repair is priced as a separate line, which the next part covers.

Repair Part Prices from Thermostats to Heat Exchangers

Homeupkeep's Melbourne guide, updated 14 June 2026, prices the common gas ducted repairs as parts and labour together. Its rows are an ignition repair at $180 to $320, a gas valve at $280 to $450, a fan motor at $320 to $580, a wired thermostat at $180 to $320, a flue repair at $380 to $680 and a heat exchanger at $1,200 to $2,800. Those rows match the components Brivis's service manual checks when a heater fails: the spark igniter and flame sensor for ignition faults, the gas valve when the burner pressure cannot be set, the main fan motor for airflow and noise, the thermostat and its wiring when the heater will not respond, and the heat exchanger and flue for combustion problems. The spread inside each row reflects the model, whether the part is a direct replacement, and how much of the heater has to be opened to reach it. Brivis's service manual has internal heaters split apart to reach the main fan, while on external models the fan assembly is removed directly, so the same part can take different labour in a roof space than in an outdoor cabinet. Better Health notes that spare parts are sometimes unavailable for older heaters, which affects both the price and the timing of a repair.

Duct Cleaning Prices by Number of Outlets

Duct cleaning is priced by the outlet, and Mr Duct Cleaning's Melbourne guide, dated 29 May 2026, shows how that works: pricing starts at $260 for 5 outlets and each additional outlet adds $10, with 6 to 10 outlets at $270 to $310. The same guide puts duct cleaning across Australia at between $200 and $700, and flat-rate jobs at $300 to $500. The Quote Yard's Victorian servicing guide, published 7 September 2026, lists duct cleaning at $250 to $600 as a separate service. Climate Control Solutions offers a combined route instead, a gas ducted service with a deep clean of the return air and ductwork at $280 to $450, against $180 to $320 for its service alone. Because the outlet count drives the price, a household can count the floor or ceiling registers in the house before asking for a quote. The ABS 2021 Census counts 66.2% of Richmond dwellings with one or two bedrooms, and a smaller home may have fewer outlets to clean, though the count in each house is what sets the figure. Access to the ducts in the roof or subfloor, and the state of the return air grille and filter, can add to the time as well.

Peak Air Conditioning Richmond

Service or Repair: Choosing the Right Booking for a Ducted Heater

A service and a repair are booked for different reasons. A service is maintenance on a heater that is working, carried out to AS 4575 on a regular interval. A repair starts from a fault: an error code on the controller, cold air from the outlets, a new noise or a flame that looks wrong. The two parts below cover when a routine service is the right booking, and how to weigh a large repair quote. If the heater shows any of the warning signs listed in the carbon monoxide section, book a gasfitter to inspect it rather than waiting for the next routine service.

Servicing Every One to Two Years While the Heater Runs Normally

When the heater lights, heats evenly and shows no errors, a routine service is the right booking, and the interval comes from the safety regulator and the manufacturer. Energy Safe Victoria recommends that all gas heaters are serviced at least every two years by a qualified gasfitter. Brivis's operation manual sets the same two-year interval, with its maintenance schedule laid out from year 2 to year 12, and Rinnai's ducted heating guidance says regular servicing is recommended. Homeupkeep's annual service contract shows that some households choose a yearly visit instead, which is a cost-guide option rather than a regulation or a manufacturer requirement. Two things can bring a service forward. A StarPro or Buffalo controller may flash its spanner symbol when the fan run hours reach the service point, and Better Health advises a service whenever there is any sign of trouble. Booking before winter, rather than when the heater is first needed, leaves time to source a part if the service finds one worn. Better Health adds that a heater not serviced for 2 years is due. For a rented home, the two-yearly gas safety check is a legal duty rather than a choice, as the carbon monoxide section explains, and a service booked at the same time can meet both.

When a Major Repair Quote Nears the Price of a New Heater

For a single part such as an igniter, a flame sensor or a thermostat, homeupkeep's repair rows sit far below the price of a new heater, so the decision is usually simple. It gets harder when the quote involves a heat exchanger, or several parts at once on an older unit, because the upper end of homeupkeep's heat exchanger range is not far below the lowest supply-and-install price the same guide gives for a new 3-star heater. No source read for this page offers a reliable rule of thumb for the point at which replacement wins, so none is given here. What the sources do say is still useful. Energy Safe Victoria suggests considering a replacement if a gas heater is old or has not been serviced for several years. Better Health notes that some heaters cannot be repaired for safety reasons, that spare parts are sometimes unavailable for older heaters, and that on a very old heater the licensed gasfitter's advice should guide the decision. The servicing record helps as well, showing whether the same fault keeps coming back. Replacement routes, from higher-star gas heaters to the age at which a heater is usually replaced, are covered on the ducted heating page, and switching to an electric heat pump is explained under reverse cycle air conditioning.

Peak Air Conditioning Richmond

Ducted Heating Repairs Richmond: Common Gas Ducted Heater Faults

Energy Safe Victoria's advice comes first: do not attempt to fix a gas heater yourself, because gas work is not a DIY project. What an owner can safely do is the short list of checks the manufacturer prints, such as resetting the heater, confirming the gas is on and making sure the outlets and the return air grille are clear. The four faults below use Brivis's own error codes and troubleshooting tables as examples. Other brands use their own codes, so the heater's own manual is the first reference, and the causes named here are the ones those manuals list, confirmed by testing on the day.

Heater Will Not Ignite or Keeps Cutting Out

A heater that will not light usually says so on the controller. On Brivis StarPro and Buffalo models, error codes 46, 47 and 55 mean the heater failed to ignite within its set time, and error 50 means it has locked out after four ignition attempts; Brivis's installer's manual says its Classic heaters try up to five times before locking out. Brivis's owner checks for error 50 are all about gas: on at the meter and at the heater's gas cock, other gas appliances in the house working, and the gas supplier confirming there are no works or supply problems in the area. If those check out, the manual says the heater may require a general service. From there, Brivis's service manual works through the ignition chain: whether a spark crosses the igniter gap, whether gas reaches the burner at the right pressure, and whether the flame sensor is clean and in position, since a dirty sensor rod can fail to confirm a flame that has in fact lit. A heater that lights and then cuts out is often an airflow problem instead. Codes 40 to 43 mean it overheated and shut off the gas, and code 53 means repeated overheating, which Brivis says is typically caused by insufficient airflow. Code 56 points to a restricted flue, and Rinnai notes that gusty wind blowing back down the flue can trigger it.

Fan Running but Cold Air from the Outlets

Cold air from the outlets has several causes, and some are normal behaviour rather than faults. Brivis's operation manual explains that at start-up the burners run for about a minute before the fan comes on, and its service manual describes a normal cool-down at the end of each heating cycle, when the fan runs on after the burners stop to clear the remaining heat. Settings come next. A Brivis heater will not heat when the room is already warmer than the set temperature, and a Fan Only setting, or a continuous fan option enabled by the installer, moves unheated air on purpose. If none of those applies, the fan may be running because the burners have stopped. When a Brivis heater overheats, its service manual says power to the gas valve is cut while the fan runs at full speed to cool the heater down, so the outlets blow cooler air until it resets, and repeated overheating then locks it out. A weak gas supply is another cause, since Brivis's service manual links low inlet pressure to reduced heat output, which leaves the air lukewarm rather than cold. The controller's error code narrows the cause down, and the fix, whether airflow, ignition or gas pressure, is traced on the day before any part is quoted.

Loud Fan Motor, Rattling or Whistling Ducts

Noise is one of the faults Brivis's operation manual tells owners to act on: if there is excessive noise, smell or smoke coming from the appliance, turn it off, isolate the power supply and contact a service agent. Some sounds have simple causes. Brivis's troubleshooting table lists a whistling noise against a dirty return air grille and filter, and cleaning both is the first remedy. A noisy fan motor is a servicing item. The service manual has the technician rotate the fan wheel and listen for scraping or worn bearings, check for a loose impeller on the motor shaft and look for signs of wear, then clean the impeller, motor and housing before reassembly. The combustion fan gets its own check for bearing or scraping noise during start-up, though Brivis notes that a light tinkling sound, made as the impeller clears water particles from the fan housing, is normal. Rattling from the ducts themselves is not covered in the manuals read for this page. As general practice, it often comes from a loose duct joint, a duct moving against a roof timber or a register cover that has worked loose, and the service manual's check that ducting is not crushed, damaged or incorrectly sized applies here too. A fan motor replacement is priced in the cost section.

One Room Cold While the Rest of the House Heats

When one room stays cold while the rest of the house warms up, the cause is usually in the outlet or the ducts rather than in the heater. The register is the first check. Brivis's commissioning settings open living areas fully, bedrooms halfway and wet areas to a quarter, so a bedroom outlet that has been knocked shut, or a register baffle left closed, delivers very little air. In a zoned house, the room may sit in a zone that is switched off. Brivis's operation manual shows zones A to D on the controller, with an arrow beside each zone that is selected, and Rinnai lists the Buffalo BX5C as ZonePlus compatible for up to 4 zones. Where a zone is selected but no air arrives, Brivis treats it as a possible installation issue, particularly on a zoned system, and the schedule's zone motors and zone controls are checked. If the outlet and the zone are both open, the duct to that room is the next suspect. Brivis's troubleshooting table asks owners to check that ducting has not been crushed or collapsed, and YourHome notes that ducts lose heat through air leakage if they are not adequately insulated and sealed. The fix may be a reconnected or replaced length of duct, a repaired zone motor, or rebalanced outlet dampers.

Peak Air Conditioning Richmond

Carbon Monoxide Safety for Gas Ducted Heaters in Richmond Homes

Energy Safe Victoria describes carbon monoxide (CO) as a poisonous, colourless and odourless gas, and notes that any gas heater can spill it, central heating units included. Because it cannot be seen or smelled, a household's defences are noticing changes in the heater, keeping an alarm as a back-up and keeping the servicing up to date. The three parts below cover what to look for, how alarms fit in, and what renters and rental providers in Richmond need to know about the two-yearly check. How the CO test itself is carried out belongs to the service section above.

Flame Colour Changes, Soot or Fumes Near the Heater

The warning sign Energy Safe Victoria names is a change in how the heater operates, for example a flame that changes from its usual colour. If there is any change, ESV says a qualified gasfitter must inspect the heater and check it for CO leakage. Better Health, the Victorian Department of Health's site, lists further signs that call for a service: a yellow or sooty flame, soot stains around the heater, walls or heater panels discoloured by heat, walls too hot to touch while the heater runs, a pilot light that goes out unexpectedly or pops or bangs when lighting, and any other sign of trouble. On a ducted system the burners sit inside a closed cabinet in the roof, under the floor or outside, so as a general observation the signs a household is more likely to see are soot around the flue terminal or staining near the unit. Brivis's service manual reads soot marks on the flue terminal or flue pipe as a sign of poor combustion. Not every mark is a combustion fault, though. Brivis notes that candles, oil burners, cooking or smoking can stain the area around outlets, and that vapour from the flue terminal while the heater runs is normal. Better Health warns that an unsafe heater can pollute a home with dangerous fumes including carbon monoxide, so either kind of sign is a reason to book an inspection rather than wait.

Carbon Monoxide Alarms as a Back-Up to Servicing

Energy Safe Victoria recommends installing a carbon monoxide alarm as a back-up measure, and says plainly that an alarm should never be a substitute for regular servicing. Its buying advice is specific: choose an alarm that complies with the United States UL2034 or the European EN50291 standard, look for one with visual and audible warnings when its electrochemical sensor or battery has expired, and follow the manufacturer's instructions on where to place it. Better Health explains why the overseas standards matter, since no Australian standard covers the design, manufacture, installation or servicing of CO alarms for homes. It adds that alarm manufacturers suggest fitting one in or near every room that has a gas heating appliance, audible from all sleeping areas. A ducted heater complicates that advice, because the heater may be in the roof, under the floor or outside while the warm air reaches every room through the outlets, so the alarm's own instructions on placement are worth reading closely. ESV also notes that an alarm's effectiveness is limited to where it is installed, as CO levels elsewhere in the room may vary. Hard-wired alarms must be installed by a licensed electrician, so a mains-powered alarm is electrical work, separate from the gas service, while ESV notes that alarms can be bought at a local hardware store and fitted to the maker's instructions.

Rented Richmond Homes: The Gas Safety Check and the Renter's Copy

Renting is the majority tenure in Richmond: the ABS 2021 Census counts 54.7% of its dwellings as rented, against 28.5% for Victoria. Consumer Affairs Victoria states that rental providers must have a gas safety check done every 2 years by a licensed or registered gasfitter, and that the gasfitter must be endorsed in the specialised class of Type A gas appliance servicing. The Building and Plumbing Commission describes what the check involves: gas installation checks, testing all gas appliances for leakage and servicing all gas appliances, with the results set down on a Record of Gas Safety Check. That record is the renter's to see. The commission says rental providers must give a copy of the gas safety check to the renter within 7 days upon request, and Better Health adds that the date of the most recent check must be provided to the renter in writing on request. For a gas ducted heater, the AS 4575 servicing record from the same visit sits alongside the safety check record, so the rental provider, the agent and the renter can each hold the same paperwork. Booking through the agent, with a window that suits the tenant, keeps both the record and the two-year deadline on track. A rented home with a gas boiler for hydronic heating falls under the same two-yearly check.

TESTIMONIALS

What Our Ducted Heating Service and Repairs Customers Say About Us

The Process

3 Step Process For Your Ducted Heating Service and Repairs Needs

Call or Book Between 6am and 10pm

Call the one number any day between 6am and 10pm. The booking notes the system type, the fault or the job, the address, who needs to be present (owner, tenant, agent or building manager) and any building access rules. Same-day visits are arranged where possible.

Inspection and Written Quote

A technician inspects the site and the existing system or the planned unit positions, then gives a written quote listing equipment, labour, extras and old unit removal. For repairs, the diagnosis comes first and any part is quoted before it is ordered. Work starts once the quote is accepted.

Installation or Repair, Testing and Handover

Each trade works under the licence it needs: ARC for refrigerant, a BPC-registered gasfitter for gas and a licensed electrician for wiring. The system is then tested, the controls are explained, and paperwork such as a Certificate of Electrical Safety or a gas compliance certificate is handed over where the job requires one.

FREQUENTLY ASKED QUESTIONS

Ducted Heating Service and Repairs In

Everything you need to know about our Ducted Heating Service and Repairs In

How much does a ducted heating service cost in Richmond?

Melbourne cost guides put a gas ducted heating service at around $180 to $320 where no faults are found (Climate Control Solutions, August 2026), and homeupkeep lists a service plus CO test at $280 to $380. A deep clean of the return air and ductwork with the service takes Climate Control Solutions' figure to $280 to $450. Repairs are priced separately as parts and labour. These are indicative ranges, not Peak Air Conditioning Richmond's own prices, and a written quote follows once the heater has been seen.

How often should ducted heating be serviced?

At least every two years. Energy Safe Victoria recommends that all gas heaters are serviced at least every two years by a qualified gasfitter, and Brivis's operation manual sets the same two-year interval for its ducted heaters. Some households choose a yearly visit, which is an option rather than a requirement. Rented homes need a gas safety check every 2 years by law, and the service section above explains what can bring a service forward.

Who can service a gas ducted heater in Victoria?

A gasfitter registered or licensed with the Building and Plumbing Commission in the specialised class of Type A appliance servicing. The commission states that only plumbers in that class can carry out Type A appliance gas servicing work, and Energy Safe Victoria classes a domestic central heater as a Type A appliance. Energy Safe Victoria suggests asking to see the licence card and checking the registered classes printed on its back. Peak Air Conditioning Richmond has this work carried out by a licensed gasfitter endorsed in that class.

Does a ducted heating service include a carbon monoxide test?

It should. Gas servicing in Victoria must be carried out in accordance with AS 4575, and the Building and Plumbing Commission describes its Appendix E checklist as including carbon monoxide testing. Some cost guides list a service plus CO test as a separate price row, so check that the written quote names the test. Brivis's maintenance schedule records the CO level in parts per million at each service, and the completed checklist comes back with the servicing record within 5 days.

Why is my ducted heating blowing cold air?

Check the settings first: the set temperature must be above the room temperature, and a Fan Only or continuous fan setting blows unheated air on purpose. Brivis heaters also run the burners for about a minute before the fan starts, and the fan runs on briefly after the burners stop. If the fan blows cool air with an error code showing, the heater may have overheated, which cuts the gas while the fan keeps running, or it may have failed to light. Those faults need a licensed gasfitter to trace, so do not open the heater yourself.

Is it worth repairing an old gas ducted heater?

For a single part such as an igniter or a thermostat, the cost guides price the repair far below a new heater, so the answer is usually yes. A heat exchanger on an old unit is a closer call. Energy Safe Victoria suggests considering replacement if a heater is old or has not been serviced for several years, and Better Health notes that some heaters cannot be repaired for safety reasons and that parts for older heaters are sometimes unavailable. A written repair quote, the servicing record and the gasfitter's advice settle it, and the ducted heating page covers the replacement options.

Request A Free Ducted Heating Service and Repairs Quote

GET A FREE QUOTE